Nissan Quest E52. Instruction — part 1034
WHEEL ALIGNMENT
RSU-7
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
• If camber is exceeds the standard value, adjust with adjusting bolt
(1) in front lower link (2).
CAUTION:
• When tightening the nut firmly and checking the torque, use
a wrench to prevent the turning of the bolt.
• After adjusting camber, be sure to check toe-in.
- If camber is not still within the specification, inspect and replace
any damaged or worn suspension parts.
TOE-IN
• If toe-in is exceeds the standard value, adjust with adjusting bolt
(1) in rear lower link (2).
CAUTION:
• Be sure to adjust equally on right and left side with adjust-
ing bolt.
• When tightening the nut firmly and checking the torque, use
a wrench to prevent the turning of the bolt.
- If toe-in is not still within the specification, inspect and replace any
damaged or worn suspension parts.
• After toe-in adjustment, adjust neutral position of steering angle
sensor. Refer to
Camber: Refer to
.
JSEIA0395ZZ
Toe-In: Refer to
JSEIA0396ZZ
RSU-8
< REMOVAL AND INSTALLATION >
REAR LOWER LINK & COIL SPRING
REMOVAL AND INSTALLATION
REAR LOWER LINK & COIL SPRING
Exploded View
INFOID:0000000009652821
Removal and Installation
INFOID:0000000009652822
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Set suitable jack under rear lower link.
CAUTION:
• At this step, the jack must be set only for supporting the removal procedure. For details on jack-
ing up the vehicle, refer to
GI-29, "Garage Jack and Safety Stand and 2-Pole Lift"
.
• Never damage the rear lower link with a jack.
• Check the stable condition when using a jack.
3.
Loosen rear lower link adjusting bolt and nut from rear suspension member, and then remove rear lower
link mounting bolt and nut from axle housing with power tool.
4.
Slowly lower jack, then remove upper seat, coil spring, and rubber seat from rear lower link.
CAUTION:
Operate while checking that jack supporting status is stable.
5.
Remove rear lower link.
6.
Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install adjusting bolt so that the graduation marks on adjusting bolt are positioned downward.
1.
Rear suspension member
2.
Radius rod
3.
Adjusting bolt
4.
Front lower link
5.
Eccentric disk
6.
Rear lower link
7.
Rubber seat
8.
Coil spring
9.
Upper seat
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSEIA0397GB
REAR LOWER LINK & COIL SPRING
RSU-9
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
• When installing upper seat (1), align protrusion (B) on upper seat
inside to tabs (A) of vehicle side bracket (2).
• Fit rubber seat (1) to step (A) of rear lower link (2).
• Fit the bottom end of coil spring to the step of rubber seat.
CAUTION:
Be careful with the vertical direction of the coil spring.
• Perform final tightening of fixing parts at the vehicle installation
position (rubber bushing), under unladen conditions with tires on
level ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000009652823
INSPECTION AFTER REMOVAL
Check rear lower link, rubber seat, upper seat, and coil spring for deformation, crack, and damage. Replace it
if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
2.
Adjust neutral position of steering angle sensor. Refer to
(with VDC).
JPEIB0266ZZ
JPEIB0013ZZ
: Upper side
JSEIA0403ZZ
RSU-10
< REMOVAL AND INSTALLATION >
REAR SHOCK ABSORBER
REAR SHOCK ABSORBER
Exploded View
INFOID:0000000009652824
Removal and Installation
INFOID:0000000009652825
REMOVAL
1.
Remove tires with power tool. Refer to
.
2.
Set jack under axle housing.
CAUTION:
• At this step, the jack must be set only for supporting the removal procedure. For details on jack-
ing up the vehicle, refer to
GI-29, "Garage Jack and Safety Stand and 2-Pole Lift"
.
• Never damage the axle housing with a jack.
• Check the stable condition when using a jack.
3.
Separate shock absorber mounting bolt from front lower link.
4.
Slowly lower jack, then remove shock absorber from front lower link.
CAUTION:
Operate while checking that jack supporting status is stable.
5.
Remove mounting bracket mounting nuts (
), and remove
shock absorber assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Shock absorber
2.
Piston rod lock nut
3.
Mounting bracket
4
Bound bumper
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JPEIB0135GB
JPEIB0060ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст