Nissan Quest E52. Instruction — part 1035
REAR SHOCK ABSORBER
RSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Perform inspection after installation. Refer to
• After replacing the shock absorber, always follow the disposal procedure to discard the shock absorber.
.
Disassembly and Assembly
INFOID:0000000009652826
DISASSEMBLY
CAUTION:
Never damage shock absorber piston rod when removing components from shock absorber.
1.
Wrap a shop cloth around lower side of shock absorber and fix it with a vise.
CAUTION:
Never set the cylindrical part of shock absorber with a vise.
2.
Secure the piston rod tip (A) so that piston rod does not turn,
and remove piston rod lock nut (1).
3.
Remove mounting bracket and bound bumper from shock
absorber.
4.
Perform inspection after disassembly. Refer to
ASSEMBLY
Note the following, and install in the reverse order of removal.
• Secure the piston rod tip (A) so that piston rod does not turn, then
tighten the piston rod lock nut (1) to the specified torque.
CAUTION:
Never reuse piston rod lock nut.
• Never damage shock absorber piston rod when installing compo-
nents from shock absorber.
• Perform inspection after assembly. Refer to
Inspection
INFOID:0000000009652827
INSPECTION AFTER DISASSEMBLY
Mounting bracket
Check for cracks and damage. Replace it if necessary.
Bound Bumper
Check for cracks and damage. Replace it if necessary.
Shock Absorber
Check the following items, and replace the part if necessary.
• Shock absorber for deformation, cracks, and other damage.
• Piston rod for damage, uneven wear, and distortion.
• Oil leakage
INSPECTION AFTER ASSEMBLY
Make sure piston rod on shock absorber is not damaged when attaching components to shock absorber.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
JPEIB0241ZZ
JPEIB0241ZZ
RSU-12
< REMOVAL AND INSTALLATION >
REAR SHOCK ABSORBER
2.
Adjust neutral position of steering angle sensor. Refer to
(with VDC).
Disposal
INFOID:0000000009652828
1.
Set shock absorber horizontally to the ground with the piston rod fully extracted.
2.
Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position (
) from top
as shown in the figure to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction show by arrow.
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3.
Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
A
: 20 – 30 mm (0.79 – 1.18 in)
JPEIA0161ZZ
RADIUS ROD
RSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
RADIUS ROD
Exploded View
INFOID:0000000009652829
Removal and Installation
INFOID:0000000009652830
REMOVAL
1.
Remove tire with power tool. Refer to
.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-120, "REAR WHEEL SENSOR : Removal and
.
3.
Remove rear lower link and coil spring. Refer to
RSU-8, "Removal and Installation"
4.
Separate shock absorber from front lower link. Refer to
RSU-10, "Removal and Installation"
5.
Separate front lower link from axle housing. Refer to
.
6.
Loosen front lower link mounting bolt and nut from suspension member. Refer to
.
7.
Remove radius rod mounting bolts and nuts from axle housing with power tool.
8.
Remove radius rod mounting bolt from rear suspension member with power tool, then remove radius rod.
9.
Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of fixing parts at the vehicle installation position (rubber bushing), under unladen
conditions with tires on level ground.
• Never reuse radius rod mounting nut.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000009652831
INSPECTION AFTER REMOVAL
Check radius rod and bushing for any deformation, cracks, or damage. Replace if necessary.
1.
Rear suspension member
2.
Radius rod
3.
Adjusting bolt
4.
Front lower link
5.
Eccentric disk
6.
Rear lower link
7.
Rubber seat
8.
Coil spring
9.
Upper seat
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSEIA0397GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст