Nissan Quest E52. Instruction — part 197
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-31
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SELF-DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
HORN WITH KEYLESS LOCK
Horn reminder function mode by Intelligent Key button can be selected from the following with
this mode
• On: Operate
• Off: Non-operation
PW DOWN SET
Unlock button pressing time on Intelligent Key button can be selected from the following with
this mode
• MODE 1: 3 sec
• MODE 2: Non-operation
• MODE 3: 5 sec
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW
NOTE:
This item is displayed, but cannot be monitored
BRAKE SW 1
Indicates [On/Off]* condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
SFT PN/N SW
Indicates [On/Off] condition of P or N position
S/L -LOCK
NOTE:
This item is displayed, but cannot be monitored
S/L -UNLOCK
NOTE:
This item is displayed, but cannot be monitored
S/L RELAY -F/B
NOTE:
This item is displayed, but cannot be monitored
UNLK SEN -DR
Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
DETE SW -IPDM
Indicates [On/Off] condition of P position
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
SFT P -MET
Indicates [On/Off] condition of P position
SFT N -MET
Indicates [On/Off] condition of N position
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
S/L LOCK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L UNLK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L RELAY-REQ
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [km/h]
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of unlock sensor
BCS-32
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status
ID OK FLAG
Indicates [Set/Reset] condition of key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
Indicates [On/Off] condition of PANIC button of Intelligent Key
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT screen is touched
• Key: Key warning chime sounds when CONSULT screen is touched
• Knob: OFF position warning chime sounds when CONSULT screen is touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
LCD
This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT screen is touched
• Engine start information displays when “BP I” on CONSULT screen is touched
• Key ID warning displays when “ID NG” on CONSULT screen is touched
• ROTAT: This item is displayed, but cannot be used.
• P position warning displays when “SFT P” on CONSULT screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: This item is displayed, but cannot be monitored
• Take away through window warning displays when “NO KY” on CONSULT screen is
touched
• Take away warning display when “OUTKEY” on CONSULT screen is touched
• OFF position warning display when “LK WN” on CONSULT screen is touched
FLASHER
This test is able to check hazard warning lamp operation
• LH: LH side hazard warning lamps operate
• RH: RH side hazard warning lamps operate
• Off: Non-operation
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-33
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)
INFOID:0000000009651701
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
P RANGE
This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation
ENGINE SW ILLUMI
This test is able to check push-button ignition switch illumination operation
• On: Operate
• Off: Non-operation
LOCK INDICATOR
This test is able to check LOCK indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation
ACC INDICATOR
This test is able to check ACC indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation
IGNITION ON IND
This test is able to check ON indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation
HORN
This test is able to check horn operation
• On: Operate
• Off: Non-operation
TRUNK/BACK DOOR
NOTE:
This item is displayed, but cannot be used
POWER SLIDE DOOR
This test is able to check automatic siding door operation
• RR PSD ON: Auto open/close operate
• RL PSD ON: Auto open/close operate
Test item
Description
Monitor item [UNIT]
Description
FR WIPER HI
[Off/On]
Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER LOW
[Off/On]
Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function.
FR WASHER SW
[Off/On]
Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER INT
[Off/On]
Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.
INT VOLUME
[1 - 7]
Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading
function.
RR WIPER ON
[Off/On]
Displays the status of the RR WIPER ON switch in combination switch judged by BCM with the combination
switch reading function.
RR WIPER INT
[Off/On]
Displays the status of the RR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.
RR WASHER SW
[Off/On]
Displays the status of the RR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
TURN SIGNAL R
[Off/On]
Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function.
TURN SIGNAL L
[Off/On]
Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
reading function.
BCS-34
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
BCM
BCM : CONSULT Function (BCM - BCM)
INFOID:0000000009651702
WORK SUPPORT
IMMU
IMMU : CONSULT Function (BCM - IMMU)
INFOID:0000000009978872
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
TAIL LAMP SW
[Off/On]
Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination
switch reading function.
HI BEAM SW
[Off/On]
Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
reading function.
HEAD LAMP SW 1
[Off/On]
Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination
switch reading function.
HEAD LAMP SW 2
[Off/On]
Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination
switch reading function.
PASSING SW
[Off/On]
Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
reading function.
AUTO LIGHT SW
[Off/On]
Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function.
FR FOG SW
[Off/On]
Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function.
Monitor item [UNIT]
Description
Item
Description
RESET SETTING VALUE
Return a value set with Work Support of each system to a default value in factory shipment.
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Monitor item
Content
CONFRM ID ALL
Indicates [YET] at all time.
Switches to [DONE] when a registered Intelligent Key backside is contacted to push-button igni-
tion switch.
CONFIRM ID4
CONFIRM ID3
CONFIRM ID2
CONFIRM ID1
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received.
Indicates [ID NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст