Nissan Quest E52. Instruction — part 893
MIR-36
< REMOVAL AND INSTALLATION >
[WITH ADP]
DOOR MIRROR
a.
Remove door mirror under cover mounting screw (A).
b.
Remove door mirror under cover mounting screws (A) and dis-
engage the fixing pawl.
c.
Remove door mirror side turn signal lamp mounting screws (A)
and remove side turn signal lamp.
8.
Remove door mirror under cover (1). (without side turn signal lamp)
a.
Remove door mirror under cover mounting screw (A).
JMLIA2188ZZ
: Pawl
JMLIA2190ZZ
JMLIA2191ZZ
JMLIA2189ZZ
DOOR MIRROR
MIR-37
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
b.
Remove door mirror under cover mounting screws (A) and dis-
engage the fixing pawl.
9.
Remove the mounting bolts (A) and remove door mirror base
from door mirror housing.
10. Remove power fold unit.
a.
Remove power fold unit assembly fixing screws (A).
b.
Remove power fold unit assembly from door mirror housing according to the numerical order shown in the
figure below.
11. Remove the mounting bolts (A) and (B), and then remove actuator bracket (1) from power fold unit (2).
ASSEMBLY
Assemble in the reverse order of disassemble.
GLASS MIRROR
GLASS MIRROR : Removal and Installation
INFOID:0000000009652720
REMOVAL
: Pawl
JMLIA2190ZZ
JMLIA1441ZZ
JMLIA0923ZZ
JMLIA0924ZZ
MIR-38
< REMOVAL AND INSTALLATION >
[WITH ADP]
DOOR MIRROR
1.
Place the glass mirror upward.
2.
As shown in the figure, insert a flat-bladed screwdriver (A) into
the recess between glass mirror (1) and actuator. Push up both
pawls simultaneously to remove glass mirror lower half side.
NOTE:
• Insert the screwdriver between the fixing pawls.
• Insert screwdriver into recesses, and push up while rotating
(twisting) to make work easier.
CAUTION:
Put a strip of protective tape (B) on housing assembly.
3.
Lift up and slide glass mirror as shown by the arrows in the fig-
ure to disengage the fixing pawls.
4.
Remove BSW indicator harness connector (A). (if equipped)
5.
Remove both terminals of mirror heater attachment (B).(if
equipped)
6.
Lightly lift up lower side of glass mirror, and detach both pawls of upper side as if pulling it out. Remove
glass mirror from actuator.
NOTE:
Be certain not to allow grease on sealing agent in center of mirror or back side of glass mirror.
INSTALLATION
Install in the reverse order of disassemble.
CAUTION:
After installation, visually check that pawls are securely engaged.
DOOR MIRROR COVER
DOOR MIRROR COVER : Removal and Installation
INFOID:0000000009652721
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
1.
Remove the glass mirror. Refer to
MIR-37, "GLASS MIRROR : Removal and Installation"
: Pawl
JMLIA2193ZZ
JMLIA2192ZZ
DOOR MIRROR
MIR-39
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
2.
With a remover tool, disengage the fixing pawls (A).
3.
Insert a remover tool between door mirror cover and mirror housing to disengage the fixing pawls, and
then remove the door mirror cover from the door mirror assembly.
INSTALLATION
Install in the reverse order of disassemble.
CAUTION:
After installation, visually check that pawls are securely engaged.
: Pawl
JMLIA1145ZZ
A
Without side turn signal lamp
B
With side turn signal lamp
: Pawl
JMLIA2196ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст