Nissan Quest E52. Instruction — part 892
MIR-32
< REMOVAL AND INSTALLATION >
[WITH ADP]
DOOR MIRROR
Models with side turn signal lamp
JMLIA2186ZZ
1.
Door mirror cover
2.
Side turn signal lamp
3.
Glass mirror
4.
Door mirror corner cover
5.
Door mirror under cover
6.
Door mirror
: Clip
: Pawl
: Always replace after every disassembly.
DOOR MIRROR
MIR-33
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Models without side turn signal lamp
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000009652718
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Be careful not to scratch or damage door mirror body when removing.
• Always replace door mirror corner cover after every disassembly.
REMOVAL
1.
Remove front door finisher. Refer to
INT-14, "Removal and Installation"
2.
Remove front door module assembly mounting bolts, pull out the front door module assembly to make
space in order to disengage the harness connector.
JMLIA2187ZZ
1.
Door mirror cover
2.
Glass mirror
3.
Door mirror corner cover
4.
Door mirror under cover
5.
Door mirror
: Clip
: Pawl
: Always replace after every disassembly.
MIR-34
< REMOVAL AND INSTALLATION >
[WITH ADP]
DOOR MIRROR
3.
Remove harness connector (A).
4.
Remove front door speaker and then, from the hole of front door
speaker disconnect the harness connectors.
5.
Peel off front door weather-strip (1), and then remove door mir-
ror mounting nuts (B).
6.
Remove door mirror corner cover.
a.
Disengage the door mirror corner cover fixing pawls with
remover tool (A). (front door side)
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
b.
Disengage the door mirror corner cover fixing pawls with
remover tool (A). (front fender side)
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
7.
Remove door mirror mounting bolt.
8.
Remove door mirror assembly from door panel.
INSTALLATION
1.
Insert door mirror harness connector through the door outer panel hole.
2.
Install door mirror assembly into the door panel and tighten the mounting bolt and nuts.
3.
Install the door mirror harness fixing clips to the door panel from the hole of door speaker.
4.
Install front door finisher.
: Clip
JMLIA2195ZZ
: Pawl
: Vehicle front
JMLIA1582ZZ
: Pawl
: Vehicle front
JMLIA1583ZZ
DOOR MIRROR
MIR-35
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DOOR MIRROR ASSEMBLY : Disassembly and Assembly
INFOID:0000000009652719
CAUTION:
When removing, always use a remover tool that is made of plastic.
DISASSEMBLY
1.
Remove door mirror assembly from the door panel. Refer to
MIR-33, "DOOR MIRROR ASSEMBLY :
.
2.
Remove glass mirror. Refer to
MIR-37, "GLASS MIRROR : Removal and Installation"
.
3.
Remove door mirror cover. Refer to
MIR-38, "DOOR MIRROR COVER : Removal and Installation"
4.
Remove door mirror actuator (1).
a.
Remove the mounting screws (A).
b.
Disconnect the harness connectors behind the actuator.
c.
Disconnect auto driving positioning harness connector (B).(if
equipped)
5.
Remove around view camera finisher assembly (1). (with around view camera)
1.
Remove around view camera finisher mounting screw (A).
2.
Disconnect harness connector (B) and remove mounting
screws (C).
3.
Disengage around view camera finisher assembly (1) fixing
pawls and remove it from door mirror housing.
6.
Remove around view camera mounting screws and then remove it from around view camera finisher.
Refer to
AV-631, "Removal and Installation"
.
7.
Remove door mirror under cover (1). (with side turn signal lamp)
JMLIA2194ZZ
JMLIA1510ZZ
: Pawl
JMLIA1508ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст