Nissan Quest E52. Instruction — part 663
SIDE PROTECT MOLDING
EXT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
• Degrease mounting surface of slide door protect molding.
• When reusing removed protect molding, apply new double-sided tape as shown in the figure, assem-
ble molding (1) and bracket (2), and then install.
• Never wash the vehicle within 24 hours so as to keep adhesive.
1.
Slide door protect molding
2.
Slide door protect molding bracket
Double-sided tape [t: 1.2 mm (0.047 in)]
JMKIA6252ZZ
EXT-28
< REMOVAL AND INSTALLATION >
FLOOR SIDE FAIRING
FLOOR SIDE FAIRING
Exploded View
INFOID:0000000009650503
Removal and Installation
INFOID:0000000009650504
REMOVAL
Remove engine under cover fixing clips, and then remove engine under cover.
INSTALLATION
Install in the reverse order of removal.
1.
Front bumper fascia assembly
2.
Engine under cover
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIA8217ZZ
ROOF SIDE MOLDING
EXT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ROOF SIDE MOLDING
Exploded View
INFOID:0000000009650505
Removal and Installation
INFOID:0000000009650506
REMOVAL
Roof side molding
1.
Remove front fender cover (LH and RH). Refer to
.
2.
Disengage roof side molding fixing pawls from front end.
1.
Roof side molding
2.
Roof side molding clip
: Pawl
JMKIA6165ZZ
: Pawl
JMKIA6166ZZ
EXT-30
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
3.
Twist and pull up to upper side, and then remove roof side mold-
ing.
CAUTION:
Never pull the roof side molding strongly.
INSTALLATION
Roof side molding
Note the following item, and then install in the reverse order of removal.
CAUTION:
When installing, check that roof side molding and installation
guide pawl are aligned normally, and then press in from rear
end toward front end.
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP
REMOVAL
1.
Remove roof side molding.
2.
Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using long-
nose pliers.
CAUTION:
Be careful not to damage the body.
INSTALLATION
1.
Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2.
Use two-part epoxy adhesive.
3.
Apply adhesive evenly to clip tape surface.
4.
Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5.
Tape roof side molding clips after press fit, and temporarily hold it for specified time based on the follow-
ing.
CAUTION:
: Pawl
JMKIA6167ZZ
: Vehicle front
JMKIA6168ZZ
Adhesive
: 3M-weld DP–105 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit
: 19.6 N
×
2 seconds
5 to 10
°
C (41 to 50
°
F)
: 1 hour or more
11 to 23
°
C (52 to 73
°
F)
: 30 minutes or more
24
°
C or more (75
°
F or more)
: 15 minutes or more
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст