Nissan Quest E52. Instruction — part 442
DLK-482
< REMOVAL AND INSTALLATION >
INTERLOCK
INTERLOCK
Exploded View
INFOID:0000000009649490
SLIDE DOOR INTERLOCK
SLIDE DOOR INTERLOCK : Removal and Installation
INFOID:0000000009649491
REMOVAL
1.
Remove rear floor step assembly. Refer to
2.
Remove slide door interlock mounting nuts.
3.
Disconnect cable (2) of fuel filler interlock assembly from slide
door interlock (1).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check slide door open/close operation.
• After installation, check fuel filler lid lock/unlock operation.
FUEL FILLER INTERLOCK
FUEL FILLER INTERLOCK : Removal and Installation
INFOID:0000000009649492
REMOVAL
1.
Remove slide door interlock. Refer to
DLK-482, "SLIDE DOOR INTERLOCK : Removal and Installation"
.
1.
Fuel filler inter lock assembly
2.
Slide door inter lock
: Clip
: N·m (kg-m, ft-lb)
JMKIA6263GB
: Vehicle front
JMKIA6284ZZ
INTERLOCK
DLK-483
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
Remove luggage side lower finisher. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER : Removal
3.
Disconnect fuel filler lid status switch connector (1), and then
remove harness connector fixing clip.
4.
Fully open fuel filler lid.
CAUTION:
Check in advance that fuel filler lid does not interfere with slide door.
5.
Remove fuel filler interlock assembly mounting nut.
6.
Remove cable fixing clips of fuel filler inter lock, and then remove fuel filler inter lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check slide door open/close operation.
• After installation, check fuel filler lid lock/unlock operation.
: Vehicle front
JMKIA6285ZZ
DLK-484
< REMOVAL AND INSTALLATION >
KEY CYLINDER
KEY CYLINDER
GLOVE BOX LID KEY CYLINDER
GLOVE BOX LID KEY CYLINDER : Exploded View
INFOID:0000000009649493
CAUTION:
After installation, check glove box assembly open/close, lock/unlock operation.
GLOVE BOX LID KEY CYLINDER : Removal and Installation
INFOID:0000000009649494
REMOVAL
1.
Remove glove box assembly. Refer to
IP-14, "Removal and Installation"
2.
Insert mechanical key (1) into glove box lid lock cylinder (2).
3.
Set glove box lid release handle (3) to the pulled-up status.
4.
Rotate mechanical key and turn glove box lid key cylinder to the
lock position.
5.
Press tumbler stopper (1) into glove box lid lock cylinder (2)
using a hook and pick tool (A), and then remove mechanical key
(3) and glove box lid lock cylinder together from glove box lid
release handle (4).
NOTE:
When removing glove box lid lock cylinder, write a short note
describing its position against glove box lid release handle.
1.
Glove box assembly
2.
Sleeve
3.
Glove box lid lock cylinder
JMKIA8272ZZ
JMKIA5490ZZ
JMKIA5491ZZ
KEY CYLINDER
DLK-485
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
6.
Remove sleeve (3) from glove box lid release handle, and then
install sleeve to glove box lid lock cylinder.
NOTE:
When removing sleeve, write a short note describing its position
against glove box lid release handle.
CAUTION:
Never pull out mechanical key (1) from glove box lid lock
cylinder (2) while sleeve is uninstalled. Otherwise, tumbler
(4) pops out of glove box lid lock cylinder.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, check glove box assembly open/close, lock/unlock operation.
JMKIA5819ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст