Nissan Quest E52. Instruction — part 1115
CURTAIN AIR BAG MODULE
SR-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000009650325
Removal and Installation
INFOID:0000000009650326
WARNING:
Always observe the following items for preventing accidental activation.
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Always work from the side of curtain air bag module. Never work in front of it.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove headlining assembly. Refer to
INT-35, "Removal and Installation"
.
2.
Disconnect the curtain air bag harness connector (front and rear).
CAUTION:
• For installing/removing the curtain air bag harness con-
nector, insert a thin screwdriver wrapped in tape into
notch, lift lock and remove the connector.
• Install the connector with lock raised, and push lock into
the connector.
• After installing the connector, check that the lock is
pushed securely into it.
1.
Curtain air bag module
: N·m (kg-m, ft-lb)
JMHIA1700GB
PHIA0953J
SR-22
< REMOVAL AND INSTALLATION >
CURTAIN AIR BAG MODULE
3.
Remove mounting bolts, and then remove the curtain air bag module.
CAUTION:
• To prevent damage to the parts, never impact the curtain air
bag module.
• Replace the curtain air bag module if it is dropped or sustains
an impact.
• To prevent accidental explosion, never insert any foreign objects (screwdriver, etc.) into the curtain
air bag module.
• To prevent accidental explosion, never disassemble the curtain air bag module.
• To prevent accidental explosion, never expose the curtain air bag module to temperatures of more
than 90
°
C (194
°
F).
• To prevent damage to the parts, never allow oil, grease, detergent, or water to come in contact with
the curtain air bag module.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check perforation of curtain air bag module to check that curtain air bag module is not twisted.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
CRASH ZONE SENSOR
SR-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CRASH ZONE SENSOR
Exploded View
INFOID:0000000009650327
Removal and Installation
INFOID:0000000009650328
WARNING:
Always observe the following items for preventing accidental activation.
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove air duct (inlet). Refer to
EM-26, "Removal and Installation"
1.
Crash zone sensor
2.
Cooling fan assembly
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA1701GB
SR-24
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
2.
Remove mounting nut (A), and then pull out the crash zone sen-
sor.
3.
Disconnect the harness connector (B), and then remove the
crash zone sensor.
CAUTION:
• To prevent damage to the parts, never impact the crash zone
sensor.
• Replace the crash zone sensor if it is dropped or sustains an
impact.
• Replace the crash zone sensor of deployed driver air bag, deployed passenger air bag, seat belt pre-
tensioner and deployed lap pre-tensioner.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse mounting nut after removal, replace with new nut.
• Never damage the harness while installing.
• Always install normally aligning to the cutout hole, because performance of the crash zone sensor
excessively fluctuates according to the installation position.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
: Vehicle front
JMHIA1702ZZ
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст