Nissan Quest E52. Instruction — part 1116
SATELLITE SENSOR
SR-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SATELLITE SENSOR
Exploded View
INFOID:0000000009650329
1.
Center pillar outer panel
2.
Front satellite sensor
3.
Front door inner panel
4.
Front door satellite sensor
5.
Rear wheel house inner panel
6.
Rear satellite sensor
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA2045GB
SR-26
< REMOVAL AND INSTALLATION >
SATELLITE SENSOR
Removal and Installation
INFOID:0000000009650330
WARNING:
Always observe the following items for preventing accidental activation.
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Never use air tools or electric tools for servicing.
FRONT DOOR SATELLITE SENSOR
Removal
1.
Remove the front door finisher. Refer to
INT-14, "Removal and Installation"
2.
Remove mounting bolt (A), and then pull out the front door satel-
lite sensor.
3.
Disconnect the harness connector (B), and then remove the
front satellite sensor.
CAUTION:
• To prevent damage to the parts, never impact the front door
satellite sensor.
• Replace the front door satellite sensor if it is dropped or sus-
tains an impact.
• Replace the front door satellite sensor of deployed side air bag module and deployed curtain air bag
module.
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse mounting bolts after removal, replace with new bolts.
• Never damage the harness while installing.
• Always install normally aligning to the cutout hole, because performance of the front door satellite
sensor excessively fluctuates according to the installation position.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
FRONT SATELLITE SENSOR
Removal
1.
Remove center pillar lower garnish. Refer to
INT-25, "CENTER PILLAR LOWER GARNISH : Removal
: Vehicle front
JMHIA2046ZZ
JMHIA0009ZZ
SATELLITE SENSOR
SR-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
2.
Remove mounting nut (A), and then pull out the front satellite
sensor.
3.
Disconnect the harness connector (B), and then remove the
front satellite sensor.
CAUTION:
• To prevent damage to the parts, never impact the front satel-
lite sensor.
• Replace the front satellite sensor if it is dropped or sustains
an impact.
• Replace the front satellite sensor of deployed side air bag module and deployed curtain air bag mod-
ule.
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse mounting nut after removal, replace with new nut.
• Never damage the harness while installing.
• Always install normally aligning to the cutout hole, because performance of the front satellite sensor
excessively fluctuates according to the installation position.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
REAR SATELLITE SENSOR
Removal
1.
Remove luggage side lower finisher. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER : Removal
2.
Remove mounting nut (A), and then pull out the rear satellite
sensor.
3.
Disconnect the harness connector (B), and then remove rear
satellite sensor.
CAUTION:
: Vehicle front
JMHIA1704ZZ
JMHIA0009ZZ
: Vehicle front
JMHIA1705ZZ
SR-28
< REMOVAL AND INSTALLATION >
SATELLITE SENSOR
• To prevent damage to the parts, never impact the rear satellite
sensor.
• Replace the rear satellite sensor if it is dropped or sustains an
impact.
• Replace the rear satellite sensor of deployed side air bag module and deployed curtain air bag mod-
ule.
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse mounting nut after removal, replace with new nut.
• Never damage the harness while installing.
• Always install normally aligning to the cutout hole, because performance of the rear satellite sensor
excessively fluctuates according to the installation position.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст