Nissan Quest E52. Instruction — part 1068
FRONT SEAT (POWER SEAT)
SE-101
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Side air bag module
5.
Reclining device inner cover (rear)
6.
Reclining device inner cover (front)
7.
Reclining device outer cover (rear)
8.
Reclining device outer cover (front)
9.
Side air bag rod
10. Seat slide rear outer cover
11.
Lower outer finisher
12. TORX bolt
13. Seat cushion outer finisher
14. Seat reclining switch knob
15. Seat slide & lifter switch knob
16. Seat switch assembly
17. Seat cushion finisher
18. Seat slide front outer cover
JMJIA9480GB
SE-102
< REMOVAL AND INSTALLATION >
FRONT SEAT (POWER SEAT)
Removal and Installation
INFOID:0000000009652988
REMOVAL
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.
NOTE:
When removing lower outer finisher, lower inner finisher, side air bag, and seat harness on driver side, operate
seat slide & seat lifter switch and set seat cushion to the highest position in advance. This facilitates removal.
1.
Remove headrest.
2.
Operate seat slide & lifter switch and slide seat to the frontmost position.
3.
Remove seat slide rear outer cover.
a.
Disengage pawls on the rear side of seat slide rear outer cover.
b.
Disengage pawls on the front side of seat slide rear outer cover.
c.
Slide seat slide rear outer cover to the rear side to remove.
4.
Remove seat slide rear inner cover.
a.
Disengage pawls on the rear side of seat slide rear inner cover.
b.
Disengage pawls on the front side of seat slide rear inner cover.
c.
Slide seat slide rear inner cover to the rear side to remove.
5.
Remove rear outer mounting TORX bolt.
6.
Remove rear inner mounting TORX bolt.
7.
Operate seat slide & lifter switch and slide seat to the rearmost position.
19. Occupant detection system control
unit
20. Seat slide front inner cover
21. Seat cushion heater unit
22. Seat cushion pad
23. Seat cushion trim
24. Seat cushion inner finisher
25. Armrest assembly
26. Armrest cap
27. Seat belt buckle trim
28. Seat harness assembly
29. Seatback lower carpet
30. Anchor bolt
31. Seat belt buckle
32. Seatback silencer
33. Seatback heater unit
34. Seatback felt
35. Seatback board
36. Seatback trim
37. Seatback pad
38. Lower inner finisher
39. Seatback hook assembly
40. Seat slide rear inner cover
41
Seat frame & adjuster assembly
: Pawl
: Metal clip
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Pawl
JMJIA4743ZZ
: Pawl
JMJIA4744ZZ
FRONT SEAT (POWER SEAT)
SE-103
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
8.
Remove seat slide front outer cover.
a.
Disengage pawls on the front side of seat slide front outer cover.
b.
Disengage pawls on the rear side of seat slide front outer cover.
c.
Slide seat slide front outer cover to the front side while lifting it
upward to remove.
9.
Remove seat slide front inner cover.
a.
Disengage pawls on the front side of seat slide front inner cover.
b.
Disengage pawls on the rear side of seat slide front inner cover.
c.
Slide seat slide front inner cover to the front side while lifting it
upward to remove.
10. Remove front outer mounting bolt.
11. Remove front inner mounting bolt.
12. Operate seat reclining switch and set the seatback vertically.
13. Disconnect seat cushion lower harness connector, and then remove harness fixing clips.
WARNING:
Never insert foreign materials, such as a screwdriver, into air bag module connector. (This is to
prevent accidental activation caused by static electricity.)
CAUTION:
Before performing removal operation, check the installation position of harness connectors and
harness fixing clamps.
14. Remove seat from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• Before tightening bolts, check that the carpet is not caught in bolt holes on mounting portion.
• Always fix the harness fixing clamp in position.
• When connecting the connector, be sure to raise lock, and then push lock into the connector to fix.
Check that the lock is engaged securely after connecting the connector.
• When installing, tighten mounting bolts to the specified
torque according to the numerical order as shown in the fig-
ure, starting from front inner mounting bolt.
For the specified torque, refer to
: Pawl
JMJIA6118ZZ
: Pawl
JMJIA6119ZZ
JMJIA6120ZZ
SE-104
< REMOVAL AND INSTALLATION >
FRONT SEAT (POWER SEAT)
NOTE:
After installing the front seat, perform additional service when removing battery negative terminal.
Refer to
SEATBACK
SEATBACK : Disassembly and Assembly
INFOID:0000000009652989
DISASSEMBLY
1.
Remove armrest assembly.
a.
Disengage pawls and remove armrest cap.
b.
Remove mounting bolt, and remove armrest assembly.
2.
Remove the seatback retainer (A), and then open seatback fas-
tener (B).
3.
Roll up seatback trim, and then remove seatback retainer (C).
4.
Remove side air bag module.
a.
Remove seatback lower carpet from the seatback trim retainer.
b.
Remove seatback trim retainer (A) and (B).
c.
Remove seat cushion lower side air bag module harness connector clip and side air bag module harness
clip.
: Pawl
JMJIA4975ZZ
JMJIA6243ZZ
JMJIA6267ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст