Nissan Quest E52. Instruction — part 1067
FRONT SEAT (MANUAL SEAT)
SE-97
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
b.
Pull seat cushion outer finisher toward seat front. Disengage
pawls and metal clips. Slide seat cushion outer finisher toward
seat front. Remove seat cushion outer finisher.
3.
Pull seat cushion inner finisher toward seat front. Disengage
pawls and metal clips. Slide seat cushion inner finisher upwards.
Remove seat cushion inner finisher.
4.
Remove seat cushion trim, seat cushion pad, and seat cushion heater unit (with heater seat only) from
seat frame & adjuster assembly.
a.
Disconnect seat cushion heater unit harness connector (A)
installed in the lower portion of seat cushion. (with heater seat
only.)
b.
Remove seatback lower carpet rubber band (1) installed in the
lower portion of seat cushion.
c.
Remove seat cushion trim, seat cushion pad, and seat cushion heater unit (with heater seat only) from
seat frame & adjuster assembly.
5.
Remove hog rings, and separate the seat cushion trim and seat cushion pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
6.
Separate the seat cushion pad and seat cushion heater unit. (with heater seat only)
7.
Remove seatback trim and seatback pad from seat frame & adjuster assembly.
Refer to
SE-90, "SEATBACK : Disassembly and Assembly"
.
8.
Remove reclining device cover.
• Disengage pawls and remove reclining device outer cover (front and rear).
• Disengage pawls and remove reclining device inner cover (front and rear).
9.
Remove following parts from seat frame & adjuster assembly.
• Remove lower outer finisher.
• Remove lower inner finisher.
• Remove seat belt buckle trim.
• Remove seat belt buckle. Refer to
SB-8, "SEAT BELT BUCKLE : Removal and Installation"
• Remove seatback board.
• Remove seatback felt.
• Remove seat harness from seat frame & adjuster assembly.
• Remove occupant detection system control unit. Refer to
SR-32, "Removal and Installation"
.
: Pawl
: Metal clip
JMJIA6220ZZ
: Pawl
: Metal clip
JMJIA6222ZZ
JMJIA6270ZZ
SE-98
< REMOVAL AND INSTALLATION >
FRONT SEAT (MANUAL SEAT)
ASSEMBLY
Note the following, and assemble in the reverse order of disassembly.
CAUTION:
• Check seat cushion trim and seat cushion pad for damage. Replace with new part if necessary.
• Install seat cushion front hog rings (A) and seat cushion back
hog rings (B) to the specified positions.
• Check the following parts for lubrication. Apply grease if necessary.
• If crimping using a hog ring is unsuccessful, secure using a new hog ring.
• Check that harness route and harness clip installation position are in the specified positions.
• When harness clip is damaged, mark the clip position and replace damaged clip with a new one in
the original position.
• Tighten seat belt buckle anchor bolt to the specified torque.
For the specified torque, refer to
JMJIA6224ZZ
A.
Active headrest rotation engage SP
bolt portion
B.
Rear lifter link sliding portion
C.
Sector gear sliding portion
D.
Recliner base core sliding portion
E.
Slide rail sliding portion
F.
Lifter lever and lifter link sliding por-
tion
G.
Seat lifter pipe (front and rear) crimp
sliding portion
1 : Heat-resistant and cold-resistant grease (Nippeco LLP or an equivalent)
2 : Heat-resistant and cold-resistant grease (RHEOGEL or an equivalent)
JMJIA6241ZZ
FRONT SEAT (POWER SEAT)
SE-99
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
FRONT SEAT (POWER SEAT)
Exploded View
INFOID:0000000009652987
DRIVER SEAT
JMJIA6114GB
SE-100
< REMOVAL AND INSTALLATION >
FRONT SEAT (POWER SEAT)
PASSENGER SEAT
1.
Seatback heater unit
2.
Seatback silencer
3.
Seat belt buckle
4.
Anchor bolt
5.
Seatback trim
6.
Seatback pad
7.
Seat harness assembly
8.
Seatback lower carpet
9.
Armrest cap
10. Armrest assembly
11.
Seat belt buckle trim
12. Seat cushion inner finisher
13. Seat cushion trim
14. Seat cushion pad
15. Seat cushion heater unit
16. Seat slide front inner cover
17. Seat control unit
18. Seat slide front outer cover
19. Seat cushion finisher
20. Seat slide & lifter switch knob
21. Seat reclining switch knob
22. Seat cushion outer finisher
23. Seat switch assembly
24. Lumber support switch assembly
25. TORX bolt
26. Lower outer finisher
27. Seat slide rear outer cover
28. Side air bag rod
29. Reclining device outer cover (front)
30. Reclining device outer cover (rear)
31. Side air bag module
32. Seatback felt
33. Seatback board
34. Headrest
35. Headrest holder (free)
36. Headrest holder (locked)
37. Seatback hook assembly
38. Reclining device inner cover (rear)
39. Reclining device inner cover (front)
40. Lower inner finisher
41. Seat slide rear inner cover
42. Seat frame & adjuster assembly
: Pawl
: Metal clip
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст