Nissan Quest E52. Instruction — part 753
HAC-142
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
COMPRESSOR DOES NOT OPERATE
COMPRESSOR DOES NOT OPERATE
Description
INFOID:0000000009652592
SYMPTOM
Compressor does not operate.
Diagnosis Procedure
INFOID:0000000009652593
NOTE:
• Perform self-diagnoses with on board diagnosis and CONSULT before performing symptom diagnosis. If
any malfunction result or DTC is detected, perform the corresponding diagnosis.
• Check that refrigerant is enclosed in cooler cycle normally. If refrigerant amount is shortage from proper
amount, perform the inspection of refrigerant leakage.
1.
CHECK MAGNET CLUTCH OPERATION
Check magnet clutch. Refer to
HAC-131, "Component Function Check"
Does it operate normally?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK REFRIGERANT PRESSURE SENSOR
Check refrigerant pressure sensor. Refer to
EC-442, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK A/C ON SIGNAL
Check A/C ON signal. Refer to
HAC-121, "Component Function Check"
Is inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK BLOWER FAN ON SIGNAL
Check blower fan ON signal. Refer to
HAC-123, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace malfunctioning parts
5.
CHECK BCM OUTPUT SIGNAL
With CONSULT
1.
Select “DATA MONITOR” mode of “ECM” using CONSULT.
2.
Select “AIR COND SIG” and “HEATER FAN SW”, and check status under the following conditions.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-36, "Removal and Installation"
NO
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
Monitor item
Condition
Status
AIR COND SIG
A/C switch
OFF (A/C indicator: OFF)
Off
ON (A/C indicator: ON)
On
HEATER FAN SW
Blower motor
OFF
Off
ON
On
FRONT A/C CONTROL
HAC-143
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
REMOVAL AND INSTALLATION
FRONT A/C CONTROL
Removal and Installation
INFOID:0000000009652594
REMOVAL
1.
Remove cluster lid C. Refer to
IP-28, "Removal and Installation"
2.
Remove fixing screws (A), and then remove front A/C control.
INSTALLATION
Install in the reverse order of removal.
JMIIA1842ZZ
HAC-144
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
REAR A/C CONTROL
REAR A/C CONTROL
Removal and Installation
INFOID:0000000009652595
REMOVAL
With Rear Display
1.
Remove roof console. Refer to
INT-35, "Removal and Installation"
.
2.
Remove fixing screws (A), and then remove rear A/C control.
Without Rear Display
1.
Disengage fixing pawls and metal clip using a remover tool (A).
2.
Disconnect harness connector, and then remove rear A/C control.
INSTALLATION
Install in the reverse order of removal.
JMIIA1843ZZ
: Pawl
: Metal clip
JMIIA1179ZZ
AMBIENT SENSOR
HAC-145
< REMOVAL AND INSTALLATION >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
AMBIENT SENSOR
Removal and Installation
INFOID:0000000009652596
REMOVAL
1.
Remove engine under cover. Refer to
EXT-23, "Removal and Installation"
.
2.
Disconnect harness connector (A).
3.
Disengage fixing pawl, and then remove ambient sensor.
INSTALLATION
Install in the reverse order of removal.
: Pawl
: Vehicle front
JMIIA1844ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст