Nissan Quest E52. Instruction — part 804
FRONT DOOR FINISHER
INT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
5.
Remove front door finisher fixing screws (A).
6.
Remove step lamp assembly. Refer to
INL-75, "Removal and Installation"
7.
Remove front door finisher.
a.
Disengage fixing clips using a remover tool (A), and then pull out
front door finisher.
CAUTION:
Insert a remover tool between door panel and clip and dis-
engage pawl.
b.
Disconnect lock knob cable (1) and inside handle cable (2), and
then remove front door finisher.
NOTE:
• Remove seat memory switch. Refer to
ADP-113, "Removal and Installation"
.
• Remove power window switch.
Front window anti-pinch. Refer to
PWC-68, "Removal and Installation"
Driver side window anti-pinch. Refer to
PWC-123, "Removal and Installation"
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
• One of the front door finisher fixing clips is not reusable. Always replace that clip after every front
door finisher disassembly. Refer to
.
• When installing, check in advance that clips are accurately aligned with the holes on door panel side,
and then install by pressing in.
JMJIA6194ZZ
: Clip
JMJIA6195ZZ
JMJIA6196ZZ
INT-16
< REMOVAL AND INSTALLATION >
SLIDE DOOR FINISHER
SLIDE DOOR FINISHER
Exploded View
INFOID:0000000009650276
1.
Rear door panel
2.
Shade hook
3.
Second roll sunshade assembly
(with roll sunshade)
4.
Slide door finisher
5.
Power window switch finisher
6.
Speaker grille
7.
Hook pin
: Clip
JMJIA6197ZZ
SLIDE DOOR FINISHER
INT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation
INFOID:0000000009650277
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the slide door panel.
REMOVAL
1.
Fully open slide door.
2.
Disengage fixing clips (B) on rear portion of door finisher using a remover tool (A).
3.
Remove slide door inside handle. Refer to
DLK-471, "INSIDE HANDLE : Removal and Installation"
4.
Disengage remaining fixing clips (B) using a remover tool (A).
5.
Pull toward the direction of the arrows as shown in the figure to
remove.
6.
Disconnect harness connector, and then remove slide door fin-
isher.
7.
Remove the following parts after removing slide door finisher.
Remove power window switch.
• Front window anti-pinch: Refer to
PWC-69, "Removal and Installation"
.
• Driver side window anti-pinch: Refer to
PWC-123, "Removal and Installation"
.
8.
Remove shade hook, if shade hook must be replaced.
: Pawl
: Vehicle front
: Clip
: Clip
JMJIA6198ZZ
JMJIA6199ZZ
JMJIA6200ZZ
INT-18
< REMOVAL AND INSTALLATION >
SLIDE DOOR FINISHER
a.
Remove hook pin using a remover tool (A).
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
b.
Pull toward vehicle lower, disengage shade hook fixing pawl,
and then remove.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check in advance that clips are accurately aligned with the holes on body panel side,
and then install by pressing in.
SECOND ROLL SUNSHADE
SECOND ROLL SUNSHADE : Disassembly
INFOID:0000000009650278
SECOND ROLL SUNSHADE : Disassembly and Assembly
INFOID:0000000009650279
CAUTION:
When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
DISASSEMBLY
1.
Remove roll sunshade assembly fixing screws (A).
: Pawl
JMJIA4864ZZ
1.
Slide door sunshade escutcheon B
2.
Roll sunshade assembly
3.
Slide door sunshade escutcheon A
: Pawl
JMJIA4827ZZ
JMJIA4831ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст