Nissan Quest E52. Instruction — part 805
SLIDE DOOR FINISHER
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2.
Using a removal tool (A), disengage fixing pawls of slide door
sunshade escutcheon A side, and then remove slide door sun-
shade escutcheon B and roll sunshade assembly as a set.
3.
Remove slide door sunshade escutcheon B.
a.
Remove slide door sunshade escutcheon B fixing screws (A).
b.
Disengage slide door sunshade escutcheon B fixing pawls, and then remove slide door sunshade
escutcheon B.
4.
Remove slide door sunshade escutcheon A.
Disengage slide door sunshade escutcheon A fixing pawls, and
then remove slide door sunshade escutcheon A.
ASSEMBLY
Assembly in the reverse order of disassembly.
: Pawl
JMJIA4832ZZ
: Pawl
JMJIA4833ZZ
: Pawl
JMJIA4834ZZ
INT-20
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
BODY SIDE TRIM
Exploded View
INFOID:0000000009650280
1.
Back pillar garnish RH
2.
Roof side garnish
3.
Shade hook
4.
Hook pin
5.
Rear pillar garnish
6.
Rear pillar garnish cap
7.
Rear body side welt
8.
Front body side welt
9.
Front pillar garnish
10.
Front pillar lower garnish
11.
Dash side finisher
12. Harness clip
13.
Rear floor step assembly
14.
Slide door striker
15. Step bracket
16.
Rear kicking plate
17.
Assist grip
18. Center pillar upper garnish
19.
Front kicking plate
20.
Center pillar lower garnish
21. Center pillar upper garnish cap
JMJIA6201ZZ
BODY SIDE TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FRONT PILLAR GARNISH
FRONT PILLAR GARNISH : Removal and Installation
INFOID:0000000009650281
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
• Fabric upholstered parts are easily damaged. Be careful while performing work and storing parts.
• Be careful not to pull out clips forcibly. Otherwise, vehicle body may be deformed.
REMOVAL
1.
Remove front body side welt. Refer to
INT-23, "BODY SIDE WELT : Removal and Installation"
.
2.
Remove front pillar garnish.
a.
Disengage front pillar garnish fixing anchor clips using a
remover tool (A).
b.
Cut anchor clip (A) portion using nippers (B).
c.
Remove front pillar garnish while lifting it upward.
d.
Remove clips remaining on body side using a remover tool.
22.
Back pillar garnish
(with auto back door)
23.
Back pillar garnish
: Clip
: Pawl
: Metal clip
: Always replace after every disassembly.
: Anchor clip
JMJIA4843ZZ
JMJIA4844ZZ
JMJIA6202ZZ
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing, check in advance that clips are accurately aligned with the holes on body panel
side, and then install by pressing in.
• Never reuse front pillar garnish fixing anchor clip. Always replace it with a new one when it is
removed.
FRONT PILLAR LOWER GARNISH
FRONT PILLAR LOWER GARNISH : Removal and Installation
INFOID:0000000009650282
CAUTION:
Never damage the body.
REMOVAL
1.
Lift up front pillar lower garnish toward vehicle upper. Disengage
front pillar lower garnish fixing pawls, and then remove front pil-
lar lower garnish.
INSTALLATION
Install in the reverse order of removal.
KICKING PLATE
KICKING PLATE : Removal and Installation
INFOID:0000000009650283
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
• Be careful not to remove harness clip without disengaging pawl of harness clip. Harness clip may
break if removed forcibly.
REMOVAL
FRONT KICKING PLATE
Disengage front kicking plate fixing clips and pawls using a remover
tool, and then remove front kicking plate.
NOTE:
Removing in the following order may allow less clips to remain on
the vehicle body side.
1.
Vehicle rear clip
2.
Vehicle front clip
3.
Vehicle front pawl
4.
Vehicle rear pawl
REAR KICKING PLATE
: Pawl
JMJIA4846ZZ
: Clip
: Pawl
JMJIA6203ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст