Nissan Quest E52. Instruction — part 1106
SEC-114
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210E STARTER RELAY
YES
>> GO TO 4.
NO
>> Replace IPDM E/R. Refer to
PCS-36, "Removal and Installation"
4.
CHECK STARTER RELAY CONTROL SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and IPDM E/R connector.
3.
Check continuity between BCM harness connector and IPDM E/R harness connector.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-98, "Removal and Installation"
NO
>> Repair or replace harness.
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
>> INSPECTION END
BCM
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M124
97
E11
46
Existed
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-115
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000009650783
DTC DETECTION LOGIC
NOTE:
If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift selector lever to the P position.
2.
Turn ignition switch ON and wait 1 second or more.
3.
Shift selector lever to the N position and wait 1 second or more.
4.
Shift selector lever to any position other than P and N, and wait 1 second or more.
5.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-115, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009650784
1.
CHECK DTC OF BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK DTC OF TCM
Check DTC in “Self Diagnostic Result” mode of “TCM” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 3.
3.
CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Disconnect TCM connector.
4.
Check continuity between IPDM E/R harness connector and TCM harness connector.
5.
Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTRLCK/PNP SW ON
There is a difference between P/N position
signal from TCM and P/N position signal
from BCM (CAN).
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
(TCM circuit is open or shorted.)
• TCM
• IPDM E/R
• BCM
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
F12
72
F23
20
Existed
SEC-116
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-36, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(–)
Continuity
IPDM E/R
Connector
Terminal
F12
72
Ground
Not existed
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-117
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000009650785
DTC DETECTION LOGIC
NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift selector lever to the P position.
2.
Turn ignition switch ON and wait 1 second or more.
3.
Shift selector lever to the N position and wait 1 second or more.
4.
Shift selector lever to any position other than P and N, and wait 1 second or more.
5.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-117, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009650786
1.
CHECK DTC OF BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK DTC OF TCM
Check DTC in “Self Diagnostic Result” mode of “TCM” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 3.
3.
CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Disconnect TCM connector.
4.
Check continuity between IPDM E/R harness connector and TCM harness connector.
5.
Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2110
INTRLCK/PNP SW OFF
There is a difference between P/N position
signal from TCM and P/N position signal
from BCM (CAN).
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
(TCM circuit is open or shorted.)
• TCM
• IPDM E/R
• BCM
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
F12
72
F23
20
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст