Nissan Quest E52. Instruction — part 1235
TM-170
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
FLUID COOLER SYSTEM
• Insert CVT fluid cooler hose according to dimension “A” described
below.
• Set hose clamps (1) from the end of CVT fluid cooler hose (2)
according to dimension “A” described below.
• Hose clamp should not interfere with the bulge.
CVT FLUID COOLER HOSE : Inspection
INFOID:0000000009650248
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
CVT OIL WARMER
CVT fluid cooler hose (1)
Insert side tube (2)
Dimension “A”
CVT fluid cooler hose A
CVT fluid cooler tube
33 mm (1.30 in)
CVT oil warmer
CVT fluid cooler hose B
Radiator
30 mm (1.18 in)
CVT fluid cooler hose C
CVT fluid cooler hose B
CVT oil warmer
CVT fluid cooler hose D
Transaxle assembly
Radiator
SCIA7203E
Dimension “A”
: 5 – 9 mm (0.20 – 0.35 in)
SCIA8123E
CVT fluid cooler hose
Hose end
Paint mark
Position of hose clamp
CVT fluid cooler hose A
CVT fluid cooler tube
Upward and 45
°
frontward
Upward and 45
°
frontward
CVT oil warmer
Frontward
Frontward
CVT fluid cooler hose B
Radiator
Upward
Upward
CVT fluid cooler hose C
CVT fluid cooler hose B
Upward
Upward
CVT oil warmer
Frontward
Frontward
CVT fluid cooler hose D
Transaxle assembly
Upward
Upward
Radiator
Backward
Backward
FLUID COOLER SYSTEM
TM-171
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CVT OIL WARMER : Exploded View
INFOID:0000000009650249
CVT OIL WARMER : Removal and Installation
INFOID:0000000009650250
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator.
CAUTION:
Perform these steps after the coolant temperature has cooled sufficiently.
1.
Remove water hose from CVT oil warmer. Refer to
TM-166, "Removal and Installation"
2.
Remove fluid cooler hose from CVT oil warmer. Refer to
TM-169, "CVT FLUID COOLER HOSE :
.
3.
Remove CVT oil warmer.
4.
Remove bracket.
INSTALLATION
Install in the reverse order of removal.
CVT OIL WARMER : Inspection
INFOID:0000000009650251
INSPECTION AFTER INSTALLATION
• Check for CVT fluid leakage and check CVT fluid level. Refer to
.
• Start the engine, and check the joints for coolant leakage. Refer to
1.
CVT oil warmer
2.
Bracket
3.
Transaxle assembly
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSDIA2321GB
TM-172
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
CVT FLUID FILTER
CVT FLUID FILTER
Exploded View
INFOID:0000000009975037
Removal and Installation
INFOID:0000000009975038
NOTE:
Cap or plug openings to prevent fluid from spilling.
REMOVAL
1.
Remove front fender protector LH. Refer to
EXT-23, "Removal and Installation"
2.
Pull out fluid cooler hose D from CVT fluid filter. Refer to
TM-169, "CVT FLUID COOLER HOSE :
.
3.
Remove filter hose.
4.
Remove CVT fluid filter from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Never reuse hose clamp.
1.
Transaxle
2.
CVT fluid filter
3.
Hose clamp
4.
Filter hose
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA4011GB
CVT FLUID FILTER
TM-173
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Install filter hose (1) and hose clamps (2) as shown in the figure.
A
: Paint mark
JSDIA4012ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст