Nissan Quest E52. Instruction — part 1233
TM-162
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
DIFFERENTIAL SIDE OIL SEAL
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000009650237
Removal and Installation
INFOID:0000000009650238
REMOVAL
RH Differential Side Oil Seal
1.
Disconnect the battery cable from the negative terminal. Refer to
PG-105, "Removal and Installation"
2.
Remove exhaust front tube. Refer to
EX-6, "Removal and Installation"
3.
Remove right front drive shaft. Refer to
FAX-19, "RIGHT SIDE : Removal and Installation"
4.
Use oil seal remover or a similar means and remove the RH differential side oil seal.
CAUTION:
When removing the differential side oil seal, be careful not to scratch the oil seal mounting sur-
faces of the transaxle case and converter housing.
LH Differential Side Oil Seal
1.
Remove left front drive shaft. Refer to
FAX-18, "LEFT SIDE : Removal and Installation"
.
2.
Use oil seal remover or a similar means and remove the LH differential side oil seal.
CAUTION:
When removing the differential side oil seal, be careful not to scratch the oil seal mounting sur-
faces of the transaxle case and converter housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse differential side oil seals.
• Apply CVT fluid to the differential side oil seal lip and around the oil seal.
• When inserting the drive shaft, be sure to use a protector (SST: KV38107900).
1.
RH differential side oil seal
2.
LH differential side oil seal
3.
Transaxle assembly
: Always replace after every disassembly.
: Apply CVT fluid
JPDIA0832ZZ
DIFFERENTIAL SIDE OIL SEAL
TM-163
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Drive each differential side oil seal evenly using the drift so that dif-
ferential side oil seal protrudes by the dimension (C) respectively.
Unit: mm (in)
NOTE:
Differential side oil seal pulling direction is used as the reference.
Drift to be used:
Inspection
INFOID:0000000009650239
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
A
: Transaxle case side
B
: Converter housing side
Dimension C
0
±
0.5 (0
±
0.020)
JPDIA0618ZZ
Location
Tool number (Kent-Moore No.)
Transaxle case side
ST33400001 (J-26082)
Converter housing side
TM-164
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
OIL PAN
OIL PAN
Exploded View
INFOID:0000000009650240
Removal and Installation
INFOID:0000000009650241
REMOVAL
1.
Remove engine under cover with power tool.
2.
Remove drain plug and then drain CVT fluid.
3.
Remove O-ring from drain plug.
4.
Remove oil pan fitting bolts (
) from oil pan.
5.
Remove oil pan.
1.
Transaxle assembly
2.
Oil pan fitting bolt
3.
Drain plug
4.
O-ring
5.
Oil pan
6.
Oil pan gasket
7.
Magnet
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Apply CVT fluid
JPDIA0608GB
: Vehicle front
SCIA8135J
OIL PAN
TM-165
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6.
Remove oil pan gasket (1) from oil pan (2).
7.
Remove magnet (3) from oil pan.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse oil pan gasket, O-ring, and oil pan fitting bolts.
• Apply CVT fluid to O-ring.
• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket mounting surface of
transaxle case and oil pan.
• Install the oil pan to the transaxle case with the following procedure.
1.
Install the oil pan gasket to the oil pan.
2.
Install the oil pan assembly to the transaxle case, and then temporarily tighten the oil pan mounting bolt.
3.
Tighten the oil pan mounting bolts in the order shown in the fig-
ure to the specified torque.
4.
Tighten the oil pan mounting bolts again clockwise from (1)
shown in the figure to the specified torque.
Inspection
INFOID:0000000009650242
INSPECTION AFTER REMOVAL
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
SCIA8219J
: Vehicle front
SCIA8264J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст