Nissan Quest E52. Instruction — part 812
BACK DOOR TRIM
INT-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BACK DOOR TRIM
Exploded View
INFOID:0000000009650306
BACK DOOR PULL HANDLE
BACK DOOR PULL HANDLE : Removal and Installation
INFOID:0000000009650307
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the back door panel.
REMOVAL
1.
Fully open the back door.
1.
Back door side finisher RH
2.
Back door upper garnish
3.
Emergency lid
4.
Back door side finisher LH
5.
Back door lower finisher cap
(without automatic back door)
6.
Automatic back door close switch
finisher
7.
Back door pull handle
8.
Back door lower finisher
: Clip
: Pawl
: Metal clip
JMJIA6261ZZ
INT-48
< REMOVAL AND INSTALLATION >
BACK DOOR TRIM
2.
Disengage back door pull handle fixing pawls using a remover
tool (A), and then remove back door pull handle.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
INSTALLING
Install in the reverse order of removal.
BACK DOOR LOWER FINISHER
BACK DOOR LOWER FINISHER : Removal and Installation
INFOID:0000000009650308
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the back door panel.
REMOVAL
1.
Fully open the back door.
2.
Remove back door pull handle. Refer to
INT-47, "BACK DOOR PULL HANDLE : Removal and Installa-
3.
Remove automatic back door close switch finisher (1) and auto-
matic back door close switch (2) as a set. (with automatic back
door)
a.
Disengage automatic back door close switch finisher fixing
pawls using a remover tool (A).
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
b.
Disconnect harness connector, and then remove automatic back door close switch finisher and automatic
back door close switch as a set.
NOTE:
Remove automatic back door close switch: Refer to
DLK-498, "Removal and Installation"
4.
Remove back door lower finisher fixing clips (A).
: Pawl
JMJIA4932ZZ
: Pawl
JMJIA4933ZZ
JMJIA4934ZZ
BACK DOOR TRIM
INT-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
5.
Disengage back door lower finisher fixing clips and pawls, and
then remove back door lower finisher.
INSTALLING
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check in advance that clips are accurately aligned with the holes on back door panel
side, and then install by pressing in.
BACK DOOR UPPER FINISHER
BACK DOOR UPPER FINISHER : Removal and Installation
INFOID:0000000009650309
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the back door panel.
REMOVAL
1.
Fully open the back door.
2.
Disengage back door upper finisher fixing clips and pawls using
a remover tool (A), and then remove back door upper finisher.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
INSTALLING
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check in advance that clips are accurately aligned with the holes on back door panel
side, and then install by pressing in.
BACK DOOR SIDE FINISHER
BACK DOOR SIDE FINISHER : Removal and Installation
INFOID:0000000009650310
CAUTION:
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
• Never damage the back door panel.
REMOVAL
1.
Fully open the back door.
2.
Remove back door lower finisher. Refer to
INT-48, "BACK DOOR LOWER FINISHER : Removal and
.
3.
Remove back door upper finisher. Refer to
INT-49, "BACK DOOR UPPER FINISHER : Removal and
.
4.
Remove back door support rod. (with automatic back door) Refer to
ROD : Removal and Installation"
.
: Clip
: Pawl
JMJIA6264ZZ
: Clip
: Pawl
JMJIA6262ZZ
INT-50
< REMOVAL AND INSTALLATION >
BACK DOOR TRIM
5.
Disengage back door side finisher fixing metal clips using a
remover tool (A), and then remove back door side finisher.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
INSTALLING
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check in advance that metal clips are accurately aligned with the holes on back door
panel side, and then install by pressing in.
EMERGENCY LID
EMERGENCY LID : Removal and Installation
INFOID:0000000009650311
CAUTION:
When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
REMOVAL
1.
Fully open the back door.
2.
Insert a remover tool (A) into cutout portion of emergency lid,
disengage pawls, and then remove emergency lid.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
INSTALLING
Install in the reverse order of removal.
: Metal clip
JMJIA6263ZZ
: Pawl
JMJIA4938ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст