Nissan Quest E52. Instruction — part 982
PWC-40
< DTC/CIRCUIT DIAGNOSIS >
[FRONT WINDOW ANTI-PINCH]
SLIDING DOOR POWER WINDOW SWITCH
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-68, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK SLIDING DOOR POWER WINDOW SWITCH
Check sliding door power window switch.
Refer to
PWC-40, "Component Inspection"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> Replace sliding door power window switch. Refer to
PWC-69, "Removal and Installation"
.
Component Inspection
INFOID:0000000009653302
1.
CHECK SLIDING DOOR POWER WINDOW SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sliding door power window switch connector.
3.
Check sliding door power window switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace sliding door power window switch. Refer to
PWC-69, "Removal and Installation"
.
Sliding door power window switch
Ground
Continuity
Connector
Terminal
LH
D88
2
Not existed
3
RH
D108
2
3
Sliding door power window switch
Condition
Continuity
Terminal
1
5
UP
Existed
3
4
2
5
NEUTRAL
3
4
1
4
DOWN
2
5
POWER WINDOW MOTOR
PWC-41
< DTC/CIRCUIT DIAGNOSIS >
[FRONT WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW MOTOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000009653303
1.
CHECK FUNCTION
Check front power window motor (driver side) operation with power window main switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-41, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000009653304
1.
CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window motor (driver side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (driver side). Refer to
GW-29, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between front power window motor (driver side) harness connector and power window
main switch harness connector.
4.
Check continuity between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-68, "Removal and Installation"
NO
>> Repair or replace harness.
PASSENGER SIDE
(+)
(-)
Condition
Voltage (V)
Front power window motor (driver side)
Connector
Terminal
D7
1
Ground
Power window main
switch
(driver side)
NEUTRAL
0 – 1
DOWN
9 – 16
2
NEUTRAL
0 – 1
UP
9 – 16
Front power window motor (driver side)
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
D7
1
D5
11
Existed
2
8
Front power window motor (driver side)
Ground
Continuity
Connector
Terminal
D7
1
Not existed
2
PWC-42
< DTC/CIRCUIT DIAGNOSIS >
[FRONT WINDOW ANTI-PINCH]
POWER WINDOW MOTOR
PASSENGER SIDE : Component Function Check
INFOID:0000000009653305
1.
CHECK FUNCTION
Check front power window motor (passenger side) operation with power window main switch or front power
window switch (passenger side).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-42, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000009653306
1.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window motor (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between front power window motor (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (passenger side). Refer to
GW-29, "Removal and Installation"
.
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Check continuity between front power window motor (passenger side) harness connector and front power
window switch (passenger side) harness connector.
4.
Check continuity between front power window motor (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side). Refer to
PWC-68, "Removal and Installa-
.
NO
>> Repair or replace harness.
SLIDING DOOR LH
(+)
(-)
Condition
Voltage (V)
Front power window motor (passenger side)
Connector
Terminal
D46
1
Ground
Front power window
switch
(passenger side)
NEUTRAL
0 – 1
DOWN
9 – 16
2
NEUTRAL
0 – 1
UP
9 – 16
Front power window motor (passenger side)
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
D46
1
D55
9
Existed
2
8
Front power window motor (passenger side)
Ground
Continuity
Connector
Terminal
D46
1
Not existed
2
POWER WINDOW MOTOR
PWC-43
< DTC/CIRCUIT DIAGNOSIS >
[FRONT WINDOW ANTI-PINCH]
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
SLIDING DOOR LH : Component Function Check
INFOID:0000000009653307
1.
CHECK FUNCTION
Check sliding door power window motor LH operation with power window main switch or sliding door power
window switch LH.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-43, "SLIDING DOOR LH : Diagnosis Procedure"
.
SLIDING DOOR LH : Diagnosis Procedure
INFOID:0000000009653308
1.
CHECK SLIDING DOOR POWER WINDOW MOTOR LH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sliding door power window motor LH connector.
3.
Turn ignition switch ON.
4.
Check voltage between sliding door power window motor LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door power window motor LH.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR POWER WINDOW MOTOR LH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect sliding door power window switch LH connector.
3.
Check continuity between sliding door power window motor LH harness connector and sliding door power
window switch LH harness connector.
4.
Check continuity between sliding door power window motor LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door power window switch LH. Refer to
PWC-69, "Removal and Installation"
NO
>> Repair or replace harness.
SLIDING DOOR RH
SLIDING DOOR RH : Component Function Check
INFOID:0000000009653309
1.
CHECK FUNCTION
(+)
(-)
Condition
Voltage (V)
Sliding door power window motor LH
Connector
Terminal
D82
1
Ground
Sliding door power
window switch LH
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Sliding door power window motor LH
Sliding door power window switch LH
Continuity
Connector
Terminal
Connector
Terminal
D82
1
D88
5
Existed
3
4
Sliding door power window motor LH
Ground
Continuity
Connector
Terminal
D82
1
Not existed
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст