Nissan Quest E52. Instruction — part 1281
REAR WIPER
WW-57
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER BLADE : Removal and Installation
INFOID:0000000009649579
REMOVAL
1.
Lift up and hold rear wiper arm. Remove rear wiper blade (1) from rear wiper arm (2) while rotating rear
wiper blade (1) in the direction indicated by the arrow as shown in the figure.
CAUTION:
Wrap wiper arm using a shop cloth so that wiper blade does not damage back door window glass.
INSTALLATION
Install in the reverse order of removal.
WIPER REFILL
WIPER REFILL : Removal and Installation
INFOID:0000000009649580
REMOVAL
1.
Remove rear wiper blade from the rear wiper arm. Refer to
WW-57, "WIPER BLADE : Removal and
.
2.
Remove rear wiper refill (2) from the end portion of rear wiper
blade (1) in the direction indicated by the arrow as shown in the
figure. Remove rear wiper refill while sliding it sideward.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• For installation of wiper refill, check that wiper refill is not twisted while installing.
• Check that wiper refill is inserted normally from the correct direction.
WIPER MOTOR
WIPER MOTOR : Removal and Installation
INFOID:0000000009649581
REMOVAL
1.
Remove rear wiper arm. Refer to
WW-55, "WIPER ARM : Removal and Installation"
.
2.
Remove back door lower finisher. Refer to
INT-48, "BACK DOOR LOWER FINISHER : Removal and
.
3.
Disconnect rear wiper motor harness connector.
4.
Remove rear wiper motor mounting nut.
5.
Raise rear waiper motor, and remove rear wiper motor from the vehicle.
CAUTION:
Never drop rear wiper motor or cause it to come into contact with other parts.
JMLIA1989ZZ
JMLIA2026ZZ
WW-58
< REMOVAL AND INSTALLATION >
REAR WIPER
6.
Remove pivot seal from the back door.
INSTALLATION
Install in the reverse order of removal.
WASHER TANK
WW-59
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER TANK
Exploded View
INFOID:0000000009649582
Removal and Installation
INFOID:0000000009649583
REMOVAL
1.
Fully open hood assembly.
1.
Washer tank inlet
2.
Washer tank inlet cap
3.
Washer tank assembly
: N·m (kg-m, in-lb)
: Vehicle front
JMLIA2134GB
WW-60
< REMOVAL AND INSTALLATION >
WASHER TANK
2.
Remove washer tank inlet fixing clip (A).
3.
Pull out washer tank inlet (1) from the washer tank.
4.
Remove fender protector RH (front). Refer to
EXT-23, "Removal and Installation"
5.
Disconnect washer pump connector (A) and washer level switch
connector (B).
6.
Remove harness fixing clips (C) from the washer tank (1).
7.
Disconnect front washer tube (3) and rear washer tube (4) from
the front & rear washer pump (2).
8.
Remove washer tank mounting bolts.
9.
Remove washer tank from the vehicle.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When installing tube to front & rear washer pump, be sure to install to front and rear correctly.
• Add water up to the top of the washer tank inlet after installing. Check that there is no leakage.
: Vehicle front
JMLIA1535ZZ
: Clip
: Vehicle front
JMLIA2152ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст