Nissan Pathfinder (2011 year). Instruction — part 605
TM-186
< REMOVAL AND INSTALLATION >
KEY INTERLOCK CABLE
4. Insert key interlock rod (A) into adjuster holder (B).
5. Install casing cap (C) to bracket (D).
6. Move slider (E) toward key interlock rod (A) to secure adjuster
holder (B) to key interlock rod (A).
7. Install instrument lower panel LH. Refer to
IP-12, "Removal and Installation"
.
8. Install the center console. Refer to
IP-21, "Removal and Installation"
JSDIA0698ZZ
2011 Pathfinder
AIR BREATHER HOSE
TM-187
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
2WD
2WD : Removal and Installation
INFOID:0000000006244882
VQ40DE Models
REMOVAL
1. Release air breather hose from clip.
2. Disconnect air breather hose from transmission tube.
3. Disconnect air breather hose from air breather tube.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Install air breather hose with paint mark at upper side.
• When installing the air breather hose, do not crush or block by folding or bending the hose.
• When inserting the hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
• Make sure clip is securely installed to bracket.
4WD
4WD : Removal and Installation
INFOID:0000000006244883
VQ40DE Models
1.
Air breather hose
2.
Transmission assembly
A.
Paint mark
B.
Clip
WCIA0663E
2011 Pathfinder
TM-188
< REMOVAL AND INSTALLATION >
AIR BREATHER HOSE
REMOVAL
1. Release air breather hose from clip.
2. Disconnect air breather hose from transmission tube.
3. Disconnect air breather hose from air breather tube.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Install air breather hose with paint mark at upper side.
• When installing an air breather hose, do not crush or block by folding or bending the hose.
• When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend portion.
• Make sure clip is securely installed to bracket.
1.
Air breather hose
2.
Transmission assembly
A.
Paint mark
B.
Clip
WCIA0664E
2011 Pathfinder
AIR BREATHER HOSE
TM-189
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
VK56DE Models
REMOVAL
1. Release air breather hose from clip.
2. Disconnect air breather hose from transmission tube.
3. Disconnect air breather hose from air breather tube.
INSTALLATION
CAUTION:
Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
1. Install each air breather hose into the breather tube (4). Set
each air breather hose with paint mark facing upward.
• A/T breather hose (1)
• Transfer breather hose (2)
• Actuator/transfer motor breather hose (3)
• Paint marks (A)
2. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (A) with the paint mark (B) facing
upward.
•
:Front
AWDIA0010ZZ
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Actuator
7.
Air breather hose clamp
8.
Clip E
9.
Transfer motor
10. Breather tube (transfer)
Vehicle front
ALDIA0110ZZ
ALDIA0111ZZ
2011 Pathfinder
TM-190
< REMOVAL AND INSTALLATION >
AIR BREATHER HOSE
3. Install clip (B) on actuator/transfer motor air breather hose (1)
and transfer air breather hose (2) with the paint mark (A)
matched.
•
:Front
4. Install actuator/transfer motor air breather hose (1) and transfer
air breather hose (2) on clip (B) and clip (C) with the paint mark
(A) and (D) facing upward.
•
:Front
5. Install the actuator air breather hose into the actuator (case con-
nector) until the hose end reaches the base of the tube. Set
actuator air breather hose with paint mark facing leftward.
6. Install clip (B) on transfer motor air breather hose (2) and trans-
fer air breather hose (1) with the paint mark (A) matched.
•
:Front
7. Install the transfer air breather hose into the breather tube
(transfer, metal connector) until the hose end reaches the base
of the tube. Set transfer air breather hose with paint mark facing
upwards.
AWDIA0011ZZ
AWDIA0012ZZ
SDIA3226E
AWDIA0013ZZ
SDIA3196E
2011 Pathfinder
AIR BREATHER HOSE
TM-191
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8. Install the transfer motor air breather hose into the transfer
motor (case connector) until the hose end reaches the end of
the curved section. Set transfer motor air breather hose with
paint mark facing leftward.
SDIA3194E
2011 Pathfinder
TM-192
< REMOVAL AND INSTALLATION >
A/T FLUID COOLER
A/T FLUID COOLER
Removal and Installation
INFOID:0000000006244884
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove front grill. Refer to
EXT-20, "Removal and Installation"
2. Remove A/T fluid cooler hoses from fluid cooler.
3. Remove A/T fluid cooler.
INSTALLATION
Installation is in the reverse order of removal.
• After completing installation, check fluid level and check for fluid leakage. Refer to
1.
A/T fluid cooler
2.
Fluid cooler tube
3.
Clip
4.
Hose clamp
5.
Cooler hose (lower)
6.
Cooler hose
7.
Tube joint
8.
Cooler hose (upper)
A.
To transmission
B.
From radiator
AWDIA0624GB
2011 Pathfinder
TRANSMISSION ASSEMBLY
TM-193
< UNIT REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000006244885
2WD : Removal and Installation
INFOID:0000000006244886
REMOVAL
CAUTION:
When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS) from
the A/T assembly.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Disconnect the negative battery terminal.
2. Remove the A/T fluid level gauge.
3. Remove front LH wheel and tire assembly. Refer to
4. Remove the front LH mud flap. Refer to
EXT-27, "Removal and Installation"
.
5. Remove the LH fender protector. Refer to
EXT-25, "Removal and Installation of Front Fender Protector"
AWDIA0622GB
1.
A/T fluid level gauge
2.
A/T fluid charging pipe
3.
O-ring
4.
Insulator
5.
A/T crossmember
6.
Copper sealing washer
7.
Bracket
8.
A/T fluid cooler tube
9.
Front crossmember
10. Transmission assembly
A. Self-sealing bolt
B. Refer to installation.
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст