Nissan Pathfinder (2011 year). Instruction — part 187
DLN-34
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: ATX14B]
P1808 VEHICLE SPEED SENSOR (ABS)
P1808 VEHICLE SPEED SENSOR (ABS)
Description
INFOID:0000000006244938
The ABS actuator and electric unit (control unit) transmits a vehicle speed signal via CAN communication to
the transfer control unit. DTC P1808 sets when a malfunction is detected in the vehicle speed signal that is
output from the ABS actuator and electric unit (control unit) or an improper signal is input while driving.
DTC Logic
INFOID:0000000006244939
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Perform self-diagnosis.
Is DTC P1808 displayed?
YES
>> Perform diagnosis procedure. Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000006244940
1.
CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Perform self-diagnosis with ABS actuator and electric unit (control unit). Refer to
.
Is any malfunction detected by self-diagnosis?
YES
>> Check the malfunctioning system.
NO
>> GO TO 2.
2.
CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to
Are the inspection results normal?
YES
>> GO TO 3.
NO
>> Check transfer control unit pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace damaged parts.
3.
CHECK DTC
Perform the self-diagnosis, after driving a vehicle for a while.
Are the inspection results normal?
YES
>> Inspection End.
NO
>> Perform self-diagnosis with ABS actuator and electric unit (control unit) again.
DTC
CONSULT-III
Diagnostic item is detected when...
Reference
[P1808]
VHCL SPEED SEN·ABS
• Malfunction is detected in vehicle
speed signal that is output from ABS
actuator and electric unit (control unit)
through CAN communication.
• Improper signal is input while driving.
Refer to
.
2011 Pathfinder
P1810 NEUTRAL-4LO SWITCH
DLN-35
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P1810 NEUTRAL-4LO SWITCH
Description
INFOID:0000000006244941
The neutral-4LO switch detects that the transfer case is in neutral or 4LO range. DTC P1810 will set when an
improper signal from the neutral-4LO switch is input due to an open or short circuit.
DTC Logic
INFOID:0000000006244942
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Perform self-diagnosis.
Is DTC P1810 displayed?
YES
>> Perform diagnosis procedure. Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000006244943
Regarding Wiring Diagram information, refer to
1.
CHECK 4LO POSITION SWITCH SIGNAL
With CONSULT-III
1. Start engine.
2. Select DATA MONITOR mode for ALL MODE AWD/4WD with CONSULT-III.
3. Read out the value of N POSI SW TF.
Without CONSULT-III
1. Start engine.
DTC
CONSULT-III
Diagnostic item is detected when...
Reference
[P1810]
4L POSI SW TF
Improper signal from neutral-4LO switch
is input due to open or short circuit.
Condition
Display value
• Vehicle stopped
• Engine running
• A/T selector lever N position
• Brake pedal depressed
4WD shift switch: 2WD,
AUTO or 4H
OFF
4WD shift switch: 4H to
4LO (While actuator mo-
tor is operating.)
OFF
→
ON
4WD shift switch: 4LO to
4H (While actuator motor
is operating.)
ON
→
OFF
4WD shift switch: 4LO
ON
2011 Pathfinder
DLN-36
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: ATX14B]
P1810 NEUTRAL-4LO SWITCH
2. Check voltage between transfer control unit harness connector
terminal and ground.
Are inspection results normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK HARNESS BETWEEN TRANSFER CONTROL UNIT AND NEUTRAL-4LO SWITCH
1. Turn ignition switch OFF. (Stay for at least 5 seconds.)
2. Disconnect transfer control unit harness connector and the neutral-4LO switch harness connector.
3. Check continuity between transfer control unit harness connec-
tor M153 terminal 25 and neutral-4LO switch harness connector
F60 terminal 13.
Also check harness for short to ground and short to power.
Are inspection results normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK GROUND CIRCUIT
1. Turn ignition switch OFF. (Stay for at least 5 seconds.)
2. Disconnect neutral-4LO switch harness connector.
3. Check continuity between neutral-4LO switch harness connec-
tor F60 terminal 12 and ground.
Also check harness for short to ground and short to power.
Are inspection results normal?
YES
>> GO TO 4.
NO
>> Repair open circuit or short to ground or short to power
in harness or connectors.
4.
CHECK 4LO SWITCH
1. Turn ignition switch OFF.
2. Disconnect neutral-4LO switch harness connector.
3. Remove neutral-4LO switch.
Connector
Terminal
(Wire col-
or)
Condition
Voltage
(Approx.)
M153
25 -
Ground
• Vehicle stopped
• Engine running
• A/T selector lever
N position
• Brake pedal de-
pressed
4WD shift switch:
2WD, AUTO or 4H
Battery
voltage
4WD shift switch: 4H to
4LO (While actuator
motor is operating.)
Battery
voltage
→
0V
4WD shift switch: 4LO
to 4H (While actuator
motor is operating.)
0V
→
Battery
voltage
4WD shift switch: 4LO
0V
SDIA2693E
Continuity should exist.
SDIA2694E
Continuity should exist.
SDIA2695E
2011 Pathfinder
P1810 NEUTRAL-4LO SWITCH
DLN-37
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4. Push and release neutral-4LO switch and check continuity
between neutral-4LO switch terminals 12 and 13.
Are inspection results normal?
YES
>> GO TO 5.
NO
>> Replace neutral-4LO switch. Refer to
5.
CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to
Are inspection results normal?
YES
>> GO TO 6.
NO
>> Check transfer control unit pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace damaged parts.
6.
CHECK DTC
Drive the vehicle and then perform self-diagnosis.
Are inspection results normal?
YES
>> Inspection End.
NO
>> Replace transfer control unit. Refer to
DLN-140, "Removal and Installation"
Component Inspection
INFOID:0000000006244944
1. Turn ignition switch OFF. (Stay for at least 5 seconds.)
2. Disconnect neutral-4LO switch harness connector.
3. Remove neutral-4LO switch. Refer to
DLN-19, "Component Parts Location"
.
4. Push and release neutral-4LO switch and check continuity
between neutral-4LO switch terminals 12 and 13.
5. If the inspection results are abnormal replace the neutral-4LO
switch.
Terminal
Condition
Continuity
12 - 13
Push neutral-4LO switch
Yes
Release neutral-4LO switch
No
SDIA2696E
Terminal
Condition
Continuity
12 - 13
Push neutral-4LO switch
Yes
Release neutral-4LO switch
No
SDIA2696E
2011 Pathfinder
DLN-38
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: ATX14B]
P1813 4WD SHIFT SWITCH
P1813 4WD SHIFT SWITCH
Description
INFOID:0000000006244945
The 4WD shift switch allows the driver to select AUTO, 2WD or 4WD and 4H or 4LO. DTC P1813 will set if
more than two switch inputs are simultaneously detected by the transfer control unit due to a short circuit in the
4WD shift switch.
DTC Logic
INFOID:0000000006244946
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Perform self-diagnosis.
Is DTC P1813 displayed?
YES
>> Perform diagnosis procedure. Refer to
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000006244947
Regarding Wiring Diagram information, refer to
1.
CHECK 4WD SHIFT SWITCH SIGNAL
With CONSULT-III
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “ALL MODE AWD/4WD” with CONSULT-III.
3. Read out ON/OFF switching action of the “2WD SWITCH”, “AUTO SWITCH”, “LOCK SWITCH” and “4L
SWITCH” while operating 4WD shift switch.
Without CONSULT-III
1. Turn ignition switch “ON”. (Do not start engine.)
2. Check voltage between transfer control unit harness connector
terminals and ground.
DTC
CONSULT-III
Diagnostic item is detected when...
Reference
[P1813]
4WD MODE SW
More than two switch inputs are simulta-
neously detected due to short circuit of
4WD shift switch.
Refer to
.
Connector
Terminal
Condition
Voltage (Ap-
prox.)
M152
9 - ground
4WD shift switch: 2WD
Battery voltage
4WD shift switch: AUTO, 4H or 4LO 0V
18 - ground
4WD shift switch: 4H
Battery voltage
4WD shift switch: 2WD, AUTO or
4LO
0V
23 - ground
4WD shift switch: 4LO
Battery voltage
4WD shift switch: 2WD, AUTO or 4H 0V
24 - ground
4WD shift switch: AUTO
Battery voltage
4WD shift switch: 2WD, 4H or 4LO
0V
WDIA0167E
2011 Pathfinder
P1813 4WD SHIFT SWITCH
DLN-39
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 2.
2.
CHECK 4WD SHIFT SWITCH POWER SUPPLY CIRCUIT
1. Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
2. Disconnect 4WD shift switch harness connector.
3. Check voltage between 4WD shift switch harness connector ter-
minal 1 and ground.
4. Turn ignition switch “ON”. (Do not start engine.)
5. Check voltage between 4WD shift switch harness connector ter-
minal 1 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check the following. If any items are damaged, repair
or replace damaged parts.
• Harness for short or open between transfer shut off
relay harness connector E155 terminal 5.
• Power supply circuit for transfer control unit. Refer to
.
3.
CHECK HARNESS BETWEEN 4WD SHIFT SWITCH AND TRANSFER CONTROL UNIT
1. Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
2. Disconnect transfer control unit harness connector and the 4WD shift switch harness connector.
3. Check continuity between the following terminals.
-
Transfer control unit harness connector M152 terminal 9 and
4WD shift switch harness connector M141 terminal 2.
-
Transfer control unit harness connector M152 terminal 18 and
4WD shift switch harness connector M141 terminal 5.
-
Transfer control unit harness connector M152 terminal 23 and
4WD shift switch harness connector M141 terminal 6.
-
Transfer control unit harness connector M152 terminal 24 and
4WD shift switch harness connector M141 terminal 3.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace damaged parts.
4.
CHECK 4WD SHIFT SWITCH
1. Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
2. Disconnect 4WD shift switch harness connector.
Connector Terminal
Voltage
(Approx.)
M141
1 - Ground
0V
WDIA0183E
Connector
Terminal
Voltage (Approx.)
M141
1 - Ground
Battery voltage
WDIA0184E
Continuity should exist.
WDIA0185E
2011 Pathfinder
DLN-40
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: ATX14B]
P1813 4WD SHIFT SWITCH
3. Operate 4WD shift switch and check continuity between 4WD
shift switch terminals.
OK or NG
OK
>> GO TO 5.
NG
>> Replace 4WD shift switch.
5.
CHECK TRANSFER CONTROL UNIT
Check transfer control unit input/output signal. Refer to
OK or NG
OK
>> GO TO 6.
NG
>> Check transfer control unit pin terminals for damage or loose connection with harness connector.
If any items are damaged, repair or replace damaged parts.
6.
CHECK DTC
Perform the self-diagnosis, after driving a vehicle for a while.
OK or NG
OK
>> Inspection End.
NG
>> Replace transfer control unit. Refer to
DLN-140, "Removal and Installation"
.
Component Inspection
INFOID:0000000006244948
4WD SHIFT SWITCH
1. Turn ignition switch “OFF”. (Stay for at least 5 seconds.)
2. Disconnect 4WD shift switch harness connector.
3. Operate 4WD shift switch and check continuity between 4WD
shift switch terminals.
Connector
Terminal
Condition
Continuity
M141
1 - 2
4WD shift switch: 2WD
Yes
4WD shift switch: AUTO, 4H and
4LO
No
1 - 3
4WD shift switch: AUTO
Yes
4WD shift switch: 2WD, 4H and
4LO
No
1 - 4
4WD shift switch: 2WD
No
4WD shift switch: AUTO, 4H and
4LO
Yes
1 - 5
4WD shift switch: 4H
Yes
4WD shift switch: 2WD, AUTO,
and 4LO
No
1 - 6
4WD shift switch: 4LO
Yes
4WD shift switch: 2WD, AUTO and
4H
No
WDIA0168E
WDIA0168E
2011 Pathfinder
P1813 4WD SHIFT SWITCH
DLN-41
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4. If NG, replace the 4WD shift switch.
Connector
Terminal
Condition
Continuity
M141
1 - 2
4WD shift switch: 2WD
Yes
4WD shift switch: AUTO, 4H and
4LO
No
1 - 3
4WD shift switch: AUTO
Yes
4WD shift switch: 2WD, 4H and
4LO
No
1 - 4
4WD shift switch: 2WD
No
4WD shift switch: AUTO, 4H and
4LO
Yes
1 - 5
4WD shift switch: 4H
Yes
4WD shift switch: 2WD, AUTO,
and 4LO
No
1 - 6
4WD shift switch: 4LO
Yes
4WD shift switch: 2WD, AUTO and
4H
No
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст