Nissan Pathfinder (2011 year). Instruction — part 200
DLN-138
< PERIODIC MAINTENANCE >
[TRANSFER: ATX14B]
TRANSFER OIL FILTER
TRANSFER OIL FILTER
Removal and Installation
INFOID:0000000006245039
REMOVAL
1. Remove the oil filter bolts and oil filter.
CAUTION:
• Do not damage center case or oil filter.
• Loosen bolts and detach oil filter evenly.
2. Remove the O-rings (1) from the oil filter (2).
3. Remove the oil filter stud from the oil filter.
4. Remove the O-ring from the oil filter stud.
INSTALLATION
1. Apply ATF to the new O-ring, and install it on the oil filter stud.
CAUTION:
Do not reuse O-ring.
2. Install the oil filter stud to the oil filter.
SMT875C
WDIA0285E
SDIA3180E
SDIA3180E
2011 Pathfinder
TRANSFER OIL FILTER
DLN-139
< PERIODIC MAINTENANCE >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
3. Apply ATF to the two new O-rings (1), and install them on the oil
filter (2).
CAUTION:
Do not reuse O-rings.
4. Install the oil filter to the transfer assembly. Tighten the bolts to
the specified torque. Refer to
CAUTION:
• Do not damage oil filter.
• Attach oil filter and tighten bolts evenly.
5. Check the transfer fluid. Refer to
6. Start the engine for one minute. Then stop the engine and
recheck the transfer fluid. Refer to
.
WDIA0285E
SDIA2136E
2011 Pathfinder
DLN-140
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
TRANSFER CONTROL UNIT
REMOVAL AND INSTALLATION
TRANSFER CONTROL UNIT
Removal and Installation
INFOID:0000000006245040
REMOVAL
1. Set transfer state as 2WD when 4WD shift switch is at 2WD, or as AUTO when 4WD shift switch is at
AUTO.
CAUTION:
When removing transfer control unit, transfer state must be at 2WD or AUTO.
2. Turn the ignition switch OFF and disconnect negative battery terminal. Refer to
.
3. Remove the instrument lower panel LH. Refer to
4. Disconnect the two transfer control unit connectors.
5. Remove the transfer control unit bolts.
6. Remove the transfer control unit.
INSTALLATION
Installation is in the reverse order of removal.
• When installing the transfer control unit, tighten bolts to the specified torque.
CAUTION:
Do not connect harness connector to transfer control unit when 4WD shift switch is at 4LO.
• After the installation, check perform self-diagnosis. Refer to
DLN-23, "CONSULT-III Function (ALL MODE
. If NG, adjust position between transfer assembly and transfer control unit. Refer to
"Precaution for Transfer Assembly and Transfer Control Unit Replacement"
.
LDIA0168E
Transfer control unit bolts : 3.4 N·m (0.35 kg-m, 30 in-lb)
2011 Pathfinder
FRONT OIL SEAL
DLN-141
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
FRONT OIL SEAL
Removal and Installation
INFOID:0000000006245041
REMOVAL
1. Remove the front propeller shaft. Refer to
DLN-318, "Removal and Installation"
.
2. Remove the companion flange self-lock nut using suitable tool.
3. Put a matching mark on top of the front drive shaft in line with
the mark on the companion flange.
CAUTION:
Use paint to make the matching mark on the front drive
shaft. Do not damage the front drive shaft.
4. Remove the companion flange using suitable tool.
5. Remove the front oil seal from the front case using Tool.
CAUTION:
Do not damage front case.
INSTALLATION
SDIA2657E
SDIA2658E
WDIA0193E
Tool number
: ST33290001 (J-34286)
LDIA0144E
2011 Pathfinder
DLN-142
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
FRONT OIL SEAL
1. Install the new front oil seal until it is flush with the end face of
the front case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Align the matching mark of the front drive shaft with the match-
ing mark of the companion flange, then install the companion
flange.
3. Install the new self-lock nut. Tighten to the specified torque
using suitable tool. Refer to
CAUTION:
Do not reuse self-lock nut.
4. Install the front propeller shaft. Refer to
.
5. Check for fluid leaks and fluid level. Refer to
Tool number
: KV38100500 ( — )
SDIA2662E
SDIA2658E
LDIA0147E
2011 Pathfinder
REAR OIL SEAL
DLN-143
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REAR OIL SEAL
Removal and Installation
INFOID:0000000006245042
REMOVAL
1. Remove the rear propeller shaft. Refer to
DLN-328, "Removal and Installation"
(2S1330),
2. Remove the dust cover from the rear case.
CAUTION:
Do not damage the rear case.
3. Remove the rear oil seal from the rear case using Tool.
CAUTION:
Do not damage the rear case.
INSTALLATION
1. Install the new rear oil seal until it is flush with the end face of the
rear case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Apply petroleum jelly to the circumference of the new dust cover.
Position the new dust cover as shown.
CAUTION:
• Do not reuse dust cover.
• Position the protursion at the position shown.
• 1: Dust cover
• 2: Rear case assembly
• A: Protrusions
WDIA0127E
Tool number
: ST33290001 (J-34286)
LDIA0139E
Tool number
: ST30720000 (J-25405)
LDIA0140E
AWDIA0550GB
2011 Pathfinder
DLN-144
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
REAR OIL SEAL
3. Install the new dust cover to the rear case using Tool.
CAUTION:
• Do not reuse dust cover.
• Apply petroleum jelly to dust cover.
4. Install the rear propeller shaft. Refer to
(2S1330),
DLN-339, "Removal and Installation"
(2S1350).
5. Refill the transfer with fluid and check for fluid leakage and fluid
.
Tool number
: KV40105310 ( — )
PDIA0116E
2011 Pathfinder
SIDE OIL SEAL
DLN-145
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SIDE OIL SEAL
Removal and Installation
INFOID:0000000006245043
REMOVAL
1. Remove the front propeller shaft. Refer to
DLN-318, "Removal and Installation"
.
2. Remove the companion flange. Refer to
DLN-288, "Disassembly and Assembly"
.
3. Remove the transfer control device from the transfer assembly. Refer to
DLN-282, "Removal and Installa-
4. Remove the side oil seal using suitable tool.
CAUTION:
Do not damage shift cross.
INSTALLATION
1. Install the new side oil seal until it is flush with the end face of
case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Install the transfer control device to the transfer assembly. Refer
DLN-282, "Removal and Installation"
3. Install the companion flange. Refer to
.
4. Install the front propeller shaft. Refer to
DLN-318, "Removal and Installation"
5. Check for fluid leaks and fluid level. Refer to
SDIA2666E
Tool number
: ST22360002 (J-25679-01)
SDIA2665E
2011 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст