Nissan Cube. Instruction — part 237
DLK-214
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
OUTSIDE HANDLE : Exploded View
INFOID:0000000009950647
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009950648
REMOVAL
1.
Remove front door finisher. Refer to
INT-12, "Removal and Installation"
2.
Fully close the front door glass.
3.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4.
Remove front door lower sash (rear). Refer to
GW-18, "Removal and Installation"
.
5.
Disconnect key rod (driver side).
6.
Disconnect door antenna and door request switch connector and remove harness clamp (with Intelligent
Key system) on outside handle bracket.
1.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
2.
Rear gasket
3.
Outside handle bracket
4.
TORX bolt
5.
Key rod (driver side)
6.
Door lock assembly
7.
Inside handle
8.
Outside handle
9.
Front gasket
: Pawl
: Vehicle front
JMKIA3960GB
FRONT DOOR LOCK
DLK-215
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
7.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
8.
While pulling outside handle, remove door key cylinder assem-
bly (diver side) or outside handle escutcheon (passenger side).
9.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
10. Remove front gasket and rear gasket.
11. While pulling outside handle bracket, slide toward rear of vehicle to remove outside handle bracket.
12. Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check door open/close, lock/unlock operation after installation.
• Check door lock cable is properly engaged with outside handle bracket.
JMKIA0020ZZ
JMKIA0560ZZ
JMKIA0524ZZ
DLK-216
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
REAR DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000009950649
DOOR LOCK : Removal and Installation
INFOID:0000000009950650
REMOVAL
1.
Remove rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
3.
Remove rear door glass. Refer to
GW-23, "Removal and Installation"
4.
Remove outside handle. Refer to
DLK-218, "OUTSIDE HANDLE : Removal and Installation"
.
5.
Remove inside handle. Refer to
DLK-217, "INSIDE HANDLE : Removal and Installation"
.
6.
Remove door lock assembly TORX bolts.
7.
Disconnect door lock actuator connector, and then remove door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check door open/close, lock/unlock operation after installation.
1.
Outside handle escutcheon
2.
Rear gasket
3.
Outside handle bracket
4.
TORX bolt
5.
Door lock assembly
6.
Inside handle
7.
Outside handle
8.
Front gasket
: Pawl
: Vehicle front
JMKIA3961GB
REAR DOOR LOCK
DLK-217
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check door lock cable is properly engaged with outside handle bracket.
INSIDE HANDLE
INSIDE HANDLE : Exploded View
INFOID:0000000009950651
INSIDE HANDLE : Removal and Installation
INFOID:0000000009950652
REMOVAL
1.
Remove rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2.
Remove inside handle mounting bolts, slide handle toward rear of vehicle, disengage handle from door
panel, and remove inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
1.
Outside handle escutcheon
2.
Rear gasket
3.
Outside handle bracket
4.
TORX bolt
5.
Door lock assembly
6.
Inside handle
7.
Outside handle
8.
Front gasket
: Pawl
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3961GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст