Nissan Cube. Instruction — part 238
DLK-218
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
OUTSIDE HANDLE : Exploded View
INFOID:0000000009950653
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009950654
REMOVAL
1.
Remove rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2.
Fully close rear door glass.
3.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
4.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
1.
Outside handle escutcheon
2.
Rear gasket
3.
Outside handle bracket
4.
TORX bolt
5.
Door lock assembly
6.
Inside handle
7.
Outside handle
8.
Front gasket
: Pawl
: Vehicle front
JMKIA3961GB
JMKIA1467ZZ
REAR DOOR LOCK
DLK-219
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
While pulling outside handle, remove outside handle escutch-
eon.
6.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
7.
Remove front gasket and rear gasket.
8.
While pulling outside handle bracket, slide toward rear of vehicle to remove outside handle bracket.
9.
Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check door open/close, lock/unlock operation after installation.
• Check door lock cable is properly engaged with outside handle bracket.
JMKIA0560ZZ
JMKIA0524ZZ
DLK-220
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR LOCK
BACK DOOR LOCK
DOOR LOCK
DOOR LOCK : Exploded View
INFOID:0000000009950655
DOOR LOCK : Removal and Installation
INFOID:0000000009950656
REMOVAL
1.
Remove back door finisher lower. Refer to
INT-27, "Removal and Installation"
.
2.
Remove sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
3.
Remove back door outside handle. Refer to
DLK-221, "OUTSIDE HANDLE : Removal and Installation"
.
4.
Remove back door lock assembly mounting bolts.
5.
Disconnect harness connector from back door lock assembly.
6.
Remove back door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check back door open/close, lock/unlock operation after installation.
• Check door lock cable is properly engaged with outside handle bracket.
OUTSIDE HANDLE
JMKIA3962GB
1.
TORX bolt
2.
Outside handle bracket
3.
Rear gasket
4.
Outside handle
5.
Outside handle escutcheon
6.
Front gasket
7.
Back door lock assembly
Refer to
for symbols in the figure.
BACK DOOR LOCK
DLK-221
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE HANDLE : Exploded View
INFOID:0000000009950657
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009950658
REMOVAL
1.
Remove back door finisher lower. Refer to
INT-27, "Removal and Installation"
.
2.
Remove sealing screeen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
3.
Disconnect back door antenna and back door request switch connector and remove harness clamp (with
intelligent key system) on outside handle bracket.
4.
Remove mounting bolt of outside handle bracket.
5.
While pulling outside handle, remove outside habdle escutch-
eon.
JMKIA3962GB
1.
TORX bolt
2.
Outside handle bracket
3.
Rear gasket
4.
Outside handle
5.
Outside handle escutcheon
6.
Front gasket
7.
Back door lock assembly
Refer to
for symbols in the figure.
JMKIA0560ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст