Nissan Cube. Instruction — part 979
TM-172
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F08B]
SHIFT LOCK SYSTEM
Without intelligent key system
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace damaged parts.
8.
CHECK STOP LAMP SWITCH (PART 1)
Check stop lamp switch. Refer to
TM-172, "Component Inspection (Stop Lamp Switch)"
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> GO TO 9.
9.
PERFORM STOP LAMP SWITCH INSTALLATION POSITION ADJUSTMENT
Perform stop lamp switch installation position adjustment. Refer to
BR-7, "Inspection and Adjustment"
.
>> GO TO 10.
10.
CHECK STOP LAMP SWITCH (PART 2)
Check stop lamp switch. Refer to
TM-172, "Component Inspection (Stop Lamp Switch)"
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
.
11.
CHECK HARNESS BETWEEN STOP LAMP SWITCH AND IGNITION SWITCH
Check continuity between stop lamp switch vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Repair or replace damaged parts.
12.
DETECT MALFUNCTIONING ITEMS
Check the following.
• 10A fuse (No.2)
• Harness for short or open between stop lamp switch and ignition switch (Refer to
• Ignition switch
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace damaged parts.
Component Inspection (Stop Lamp Switch)
INFOID:0000000009949052
1.
CHECK STOP LAMP SWITCH
Check continuity between stop lamp switch connector terminals.
CVT shift selector vehicle side harness connector
Ground
Continuity
Connector
Terminal
M57
5
Not existed
Stop lamp switch vehicle side harness connector
Ground
Continuity
Connector
Terminal
E115
3
Not existed
SHIFT LOCK SYSTEM
TM-173
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
.
Component Inspection (Shift Lock Solenoid)
INFOID:0000000009949053
1.
CHECK SHIFT LOCK SOLENOID
Apply voltage to CVT shift selector connector terminal and park position switch connector terminal then check
that shift lock solenoid is activated.
CAUTION:
Before applying voltage, always install a fuse between battery positive terminal and CVT shift selector
connector terminal.
With intelligent key system
Without intelligent key system
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace CVT shift selector. Refer to
.
Component Inspection (Park Position Switch)
INFOID:0000000009949054
1.
CHECK PARK POSITION SWITCH
Check continuity between park position switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace park position switch. Refer to
.
Stop lamp switch connector
Condition
Continuity
Connector
Terminal
E115
1
2
Depressed brake pedal
Existed
Brake pedal not depressed
Not existed
3
4
Depressed brake pedal
Existed
Brake pedal not depressed
Not existed
CVT shift selector connector
Park position switch connector
Condition
Status
Connector
Terminal
Connector
Terminal
M58
5
M325
1
Impress battery voltage to CVT
shift selector connector terminal
5.
Shift lock solenoid
operates
CVT shift selector connector
Park position switch connector
Condition
Status
Connector
Terminal
Connector
Terminal
M57
5
M325
1
Impress battery voltage to CVT
shift selector connector terminal
5.
Shift lock solenoid
operates
Park position switch connector
Condition
Continuity
Connector
Terminal
M325
1
2
Park position switch: ON
Existed
Park position switch: OFF
Not existed
TM-174
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F08B]
TCM
ECU DIAGNOSIS INFORMATION
TCM
Reference Value
INFOID:0000000009949055
VALUES ON THE DIAGNOSIS TOOL
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item
Condition
Value / Status (Approx.)
VSP SENSOR
During driving
Approximately matches the
speedometer reading.
ESTM VSP SIG
During driving
Approximately matches the
speedometer reading.
PRI SPEED SEN
During driving (Lock-up ON)
Approximately matches the en-
gine speed.
ENG SPEED SIG
Engine running
Closely matches the tachometer
reading.
SEC HYDR SEN
• Selector lever: “N” position
• Idle speed
0.8 V
ATF TEMP SEN
CVT fluid temperature: 20
°
C (68
°
F)
2.01 – 2.05 V
CVT fluid temperature: 50
°
C (122
°
F)
1.45 – 1.50 V
CVT fluid temperature: 80
°
C (176
°
F)
0.90 – 0.94 V
VIGN SEN
Ignition switch: ON
Battery voltage
VEHICLE SPEED
During driving
Approximately matches the
speedometer reading.
PRI SPEED
During driving (Lock-up ON)
Approximately matches the en-
gine speed.
SEC SPEED
During driving
50 X (Approximately matches the
speedometer reading.)
ENG SPEED
Engine running
Closely matches the tachometer
reading.
GEAR RATIO
During driving
2.56 – 0.43
ACC PEDAL OPEN
Released accelerator pedal - Fully depressed accelerator pedal
0.0/8 – 8.0/8
SEC PRESS
• Selector lever: “N” position
• Idle speed
0 – 1 MPa
ATFTEMP COUNT
*1
CVT fluid temperature: 20
°
C (68
°
F)
47
CVT fluid temperature: 50
°
C (122
°
F)
104
CVT fluid temperature: 80
°
C (176
°
F)
161
STM STEP
During driving
−
7 step – 171 step
ISOLT1
Lock-up “OFF”
0 A
Lock-up “ON”
0.7 A
ISOLT2
Line pressure low
0.8 A
Line pressure high
0 A
ISOLT3
Secondary pressure low - Secondary pressure high
0.8 – 0 A
SOLMON1
Lock-up “OFF”
0 A
Lock-up “ON”
0.7 A
TCM
TM-175
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SOLMON2
• Selector lever: “N” position
• Idle speed
0.8 A
Stall speed
0.3 – 0.6 A
SOLMON3
• Selector lever: “N” position
• Idle speed
0.6 – 0.7 A
Stall speed
0.4 – 0.6 A
BRAKESW
Depressed brake pedal
On
Brake pedal not depressed
Off
FULL SW
Fully depressed accelerator pedal
On
Released accelerator pedal
Off
IDLE SW
After engine is warmed up, release accelerator pedal
On
Fully depressed accelerator pedal
Off
SPORT MODE SW
Press and hold overdrive control switch
On
Other conditions
Off
INDLRNG
Selector lever: “L” position
On
Other conditions
Off
INDDRNG
Selector lever: “D” position
On
Other conditions
Off
INDNRNG
Selector lever: “N” position
On
Other conditions
Off
INDRRNG
Selector lever: “R” position
On
Other conditions
Off
INDPRNG
Selector lever: “P” position
On
Other conditions
Off
SPORT MODE IND
When overdrive OFF condition
On
Other conditions
Off
SMCOIL D
During driving
Changes On
⇔
Off
SMCOIL C
During driving
Changes On
⇔
Off
SMCOIL B
During driving
Changes On
⇔
Off
SMCOIL A
During driving
Changes On
⇔
Off
LUSEL SOL OUT
Selector lever: “P” and “N” positions
On
Wait at least for 5 seconds with the selector lever in “R”, “D” and “L”
positions
Off
LUSEL SOL MON
Selector lever: “P” and “N” positions
On
Wait at least for 5 seconds with the selector lever in “R”, “D” and “L”
positions
Off
VDC ON
VDC operate
On
Other conditions
Off
TCS ON
TCS operate
On
Other conditions
Off
ABS ON
ABS operates
On
Other conditions
Off
RANGE
Selector lever: “P” and “N” positions
N·P
Selector lever: “R” position
R
Selector lever: “D” position
D
Selector lever: “L” position
L
Monitor item
Condition
Value / Status (Approx.)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст