Nissan Cube. Instruction — part 991
TM-220
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
CONTROL CABLE
When installing control cable (1) to CVT shift selector assembly (2),
check that control cable is fully pressed in with the ribbed (A) surface
facing upward.
Inspection
INFOID:0000000009949086
INSPECTION AFTER INSTALLATION
Check the CVT position. Refer to
TM-215, "Inspection and Adjustment"
.
: Vehicle front
JPDIA0136ZZ
KEY INTERLOCK CABLE
TM-221
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
KEY INTERLOCK CABLE
Exploded View
INFOID:0000000009949087
Removal and Installation
INFOID:0000000009949088
REMOVAL
CAUTION:
Make sure that parking brake is applied before removal/installation.
1.
Remove selector lever knob. Refer to
2.
Remove center console. Refer to
3.
Slide slider (A) toward casing cap (B) while pressing tabs (C) on slider to separate slider from adjust
holder (D).
4.
Remove steering column cover lower and instrument driver lower panel. Refer to
.
1.
Key cylinder
2.
CVT shift selector assembly
3.
key interlock cable
A.
Lock plate
Refer to
JSDIA1297ZZ
E
: Key interlock rod
SCIA6975E
TM-222
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
KEY INTERLOCK CABLE
5.
Pull out the lock plate (A) from the holder (B).
6.
Remove the key interlock cable (1) from the key cylinder (2).
7.
Remove clip and remove key interlock cable.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Temporarily install adjust holder (A) to key interlock rod (B). Install
casing cap (C) to cable bracket (D) on CVT shift selector assem-
bly.
CAUTION:
• Never bend or twist key interlock cable excessively when
installing.
• Check that casing cap is firmly secured in cable bracket on
CVT shift selector assembly after installing key interlock
cable to cable bracket on CVT shift selector assembly.
• Slide the slider (A) toward the key interlock rod (D) while pressing
the pull lock (B) down to securely connect the adjust holder (C)
with the key interlock rod (D).
CAUTION:
• Never press tabs when holding slider.
• Never apply any force at a right angle to key interlock rod
when sliding.
Inspection
INFOID:0000000009949089
INSPECTION AFTER INSTALLATION
Check the CVT position. Refer to
TM-215, "Inspection and Adjustment"
.
JSDIA1308ZZ
SCIA6188E
SCIA6978E
TCM
TM-223
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
TCM
Exploded View
INFOID:0000000009949090
Removal and Installation
INFOID:0000000009949091
REMOVAL
CAUTION:
When replacing TCM and transaxle assembly as a set, replace transaxle assembly first and then
replace TCM. Refer to
.
1.
Disconnect the battery cable from the negative terminal. Refer to
PG-82, "Removal and Installation"
2.
Disconnect TCM connector.
3.
Remove TCM.
INSTALLATION
Install in the reverse order of removal.
Adjustment
INFOID:0000000009949092
ADJUSTMENT AFTER INSTALLATION
Perform “ADDITIONAL SERVICE WHEN REPLACING TCM”. Refer to
1.
TCM
Refer to
JSDIA1232GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст