Nissan Cube. Instruction — part 992
TM-224
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
AIR BREATHER HOSE
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000009949093
REMOVAL
1.
Remove clip from air cleaner assembly.
2.
Remove air breather hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Check that air breather hose is not collapsed or blocked due to folding or bending when installed.
• Fix clip to mounting hole.
• Check that insertion allowance of hose to transaxle tube is end reaches radius curve end.
• When inserting air breather hose to transaxle tube, check that paint mark faces vehicle upper side.
OIL PAN
TM-225
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000009949094
Removal and Installation
INFOID:0000000009949095
REMOVAL
1.
Remove engine under cover.
2.
Remove drain plug from oil pan and then drain the CVT fluid.
3.
Remove oil pan fitting bolts (
), and then remove oil pan and oil
pan gasket.
4.
Remove magnets from oil pan.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Transaxle assembly
2.
Oil pan fitting bolt
3.
Drain plug
4.
Drain plug gasket
5.
Oil pan
6.
Oil pan gasket
7.
Magnet
Refer to
JSDIA2985GB
: Vehicle front
JSDIA2850ZZ
TM-226
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
OIL PAN
CAUTION:
• Never reuse oil pan gasket and drain plug gasket.
• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket mounting surface of
transaxle case and oil pan.
Inspection
INFOID:0000000009949096
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
PRIMARY SPEED SENSOR
TM-227
< REMOVAL AND INSTALLATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PRIMARY SPEED SENSOR
Exploded View
INFOID:0000000009949097
Removal and Installation
INFOID:0000000009949098
REMOVAL
1.
Remove battery. Refer to
.
2.
Remove air duct (inlet), air duct and air cleaner case. Refer to
.
3.
Remove battery bracket.
4.
Remove control cable from instruction lever. Refer to
.
5.
Place instruction lever to “L” position.
6.
Disconnect primary speed sensor connector.
7.
Remove primary speed sensor.
8.
Remove O-ring from primary speed sensor.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000009949099
INSPECTION AFTER INSTALLATION
• Check for CVT fluid leakage and check CVT fluid level. Refer to
.
• Check the CVT position. Refer to
TM-215, "Inspection and Adjustment"
1.
Primary speed sensor
2.
O-ring
3.
Transaxle assembly
: Apply CVT Fluid NS-2.
Refer to
for symbols not described above.
JSDIA0750GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст