Nissan Cube. Instruction — part 944
TM-32
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
Disassembly
INFOID:0000000009948882
1.
Remove drain plug and gasket from clutch housing, using a socket [Commercial service tool] and then
drain gear oil.
2.
Remove filler plug and gasket from transaxle case.
3.
Remove selector lever (1) retaining pin with a pin punch to
remove selector lever.
4.
Remove bracket (2) and position switch (3) from transaxle case.
1.
Shim
2.
Differential side bearing outer race
(transaxle case side)
3.
Differential side bearing inner race
(transaxle case side)
4.
Final gear
5.
Differential case
6.
Speedometer drive gear
7.
Differential side bearing inner race
(clutch housing side)
8.
Differential side bearing outer race
(clutch housing side)
: Replace the parts as a set.
Refer to
for symbols not described on the above.
JPDIC0604GB
PCIB1693E
TRANSAXLE ASSEMBLY
TM-33
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5.
Remove transaxle case mounting bolts (
).
6.
Remove reverse idler shaft mounting bolt (
) and seal washer.
7.
Remove transaxle case (2) while rotating shifter lever A (1) in
the direction as shown in the figure.
8.
Remove selector spring (1) from return bushing (A).
9.
Shift 1st-2nd fork rod (1), fork rod (2), and reverse fork rod (3) to
the neutral position.
10. Remove selector (4) from clutch housing.
PCIB1694E
PCIB1695E
JPDIC0444ZZ
JPDIC0445ZZ
PCIB1698E
TM-34
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
11. Remove reverse idler shaft assembly (1) according to the follow-
ing procedures.
a.
Pull up input shaft assembly (2), mainshaft assembly (3), fork
rod (4), and 1st-2nd fork rod (5).
NOTE:
It is easier to pull up when shifting each fork rod to each shaft
side.
b.
Remove reverse idler shaft assembly and reverse fork rod (6)
from clutch housing.
12. Remove spring washer from clutch housing.
13. Pull up and remove input shaft assembly (1), mainshaft assem-
bly (2), fork rod (3), and 1st-2nd fork rod (4) from clutch housing.
NOTE:
It is easier to pull up when shifting each fork rod to each shaft
side.
14. Remove final drive assembly (1) from clutch housing.
15. Remove magnet from clutch housing.
16. Remove differential side oil seals (1) from clutch housing and
transaxle case.
CAUTION:
Never damage clutch housing and transaxle case.
17. Remove differential side bearing outer race (1) from clutch hous-
ing, using a brass rod.
CAUTION:
Never damage clutch housing.
JPDIC0606ZZ
JPDIC0607ZZ
PCIB1703E
PCIB1704E
PCIB1716E
TRANSAXLE ASSEMBLY
TM-35
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
18. Remove differential side bearing outer race (1) from transaxle
case, using a brass rod.
CAUTION:
Never damage transaxle case.
19. Remove shim (2) from transaxle case.
20. Remove shifter lever A (1) retaining pin, using a pin punch.
21. Remove shifter lever A from transaxle case.
22. Remove shifter lever B (1) from transaxle case.
23. Remove oil gutter (1) from transaxle case.
24. Remove bushings (1) from transaxle case, using a remover
[Commercial service tool].
CAUTION:
Never damage transaxle case.
PCIB1705E
JPDIC0106ZZ
PCIB1712E
PCIB1707E
PCIB1710E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст