Nissan Cube. Instruction — part 942
TM-24
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
POSITION SWITCH
1.
Remove air duct (inlet). Refer to
EM-24, "Removal and Installation"
2.
Remove battery. Refer to
PG-82, "Removal and Installation"
3.
Remove clips from the air cleaner case and air duct. Refer to
TM-22, "Removal and Installation"
.
4.
Remove air cleaner case and air ducts. Refer to
EM-24, "Removal and Installation"
.
5.
Remove bracket (1).
6.
Disconnect position switch connector.
7.
Remove position switch from transaxle case.
INSTALLATION
1.
Apply recommended sealant to threads of position switch.
• Use Genuine Silicone RTV or an equivalent. Refer to
GI-22, "Recommended Chemical Products and
.
CAUTION:
Remove old sealant and oil adhering to threads.
2.
Install position switch to transaxle case.
3.
Tighten position switch to the specified torque. Refer to
4.
For the next step and after, install in the reverse order of removal.
: Vehicle front
JPDIC0660ZZ
TRANSAXLE ASSEMBLY
TM-25
< UNIT REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000009948878
Removal and Installation
INFOID:0000000009948879
CAUTION:
Never reuse CSC (Concentric Slave Cylinder). Because CSC slides back to the original position every
time when removing transaxle assembly. At this timing, dust on the sliding parts may damage a seal of
CSC and may cause clutch fluid leakage. Refer to
CL-17, "Removal and Installation"
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Remove air duct (inlet). Refer to
EM-24, "Removal and Installation"
3.
Remove battery. Refer to
PG-82, "Removal and Installation"
4.
Remove clips from air cleaner case and air duct. Refer to
TM-22, "Removal and Installation"
.
5.
Remove air cleaner case and air ducts. Refer to
EM-24, "Removal and Installation"
.
6.
Remove air breather hose. Refer to
TM-22, "Removal and Installation"
.
7.
Remove bracket (1).
8.
Disconnect position switch connector.
9.
Remove harness clip from transaxle assembly.
10. Disconnect selector cable and shifter cable from transaxle
assembly. Refer to
TM-19, "Removal and Installation"
11. Remove starter motor. Refer to
STR-26, "Removal and Installa-
12. Remove clutch tube from CSC (Concentric Slave Cylinder).
CL-15, "Removal and Installation"
.
CAUTION:
• Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immedi-
ately and wash the affected area with water.
1.
Transaxle assembly
: Refer to "INSTALLATION" in
TM-25, "Removal and Installation"
for the locations and tightening torque.
JPDIC0632ZZ
: Vehicle front
JPDIC0660ZZ
TM-26
< UNIT REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
TRANSAXLE ASSEMBLY
• Never depress clutch pedal during removal procedure.
13. Remove engine under cover.
14. Remove fender protector LH. Refer to
EXT-21, "FENDER PROTECTOR : Removal and Installation"
.
15. Disconnect ground cable.
16. Remove front drive shafts. Refer to
FAX-16, "LEFT SIDE : Removal and Installation"
"RIGHT SIDE : Removal and Installation"
NOTE:
Insert a suitable plug into differential side oil seal after removing front drive shaft.
17. Set a suitable jack to transaxle assembly and then set a suitable jack to engine assembly.
CAUTION:
When setting a suitable jack, be careful so that it does not contact with the switch.
18. Remove engine mounting bracket (LH) mounting bolts (
) from
transaxle assembly. Refer to
EM-74, "Removal and Installation"
.
19. Remove rear engine mounting bracket and rear torque rod.
EM-74, "Removal and Installation"
20. Remove transaxle assembly mounting bolts, using a power tool
[Commercial service tool].
21. Remove transaxle assembly from the engine.
CAUTION:
• Fix transaxle assembly to a suitable jack.
• The transaxle assembly must not interfere with the wire harnesses and clutch tube.
22. Remove CSC (Concentric Slave Cylinder). Refer to
CL-17, "Removal and Installation"
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Fix transaxle assembly to a suitable jack.
• The transaxle assembly must not interfere with the wire harnesses and clutch tube.
• When installing transaxle assembly, never bring input shaft into contact with clutch cover.
• Tighten transaxle assembly mounting bolts to the specified torque.
The figure is the view from the engine.
Inspection
INFOID:0000000009948880
INSPECTION AFTER INSTALLATION
• Check the control linkage. Refer to
.
• Check the oil leakage and the oil level. Refer to
.
: Vehicle front
JPDIC0661ZZ
: Transaxle to engine
: Engine to transaxle
Bolt symbol
A
B
Quantity
3
6
Bolt length
“
” mm (in)
60 (2.36)
50 (1.97)
Tightening torque
N·m (kg-m, ft-lb)
62.0 (6.3, 46)
JPDIC0094ZZ
TRANSAXLE ASSEMBLY
TM-27
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000009948881
CASE AND HOUSING
1.
Filler plug
2.
Gasket
3.
Transaxle case
4.
Bushing
5.
Snap ring
6.
Oil channel
7.
Oil gutter
8.
Position switch
9.
Bracket
10. Differential side oil seal
11. Magnet
12. Drain plug
13. Input shaft oil seal
14. Clutch housing
15. 2 way connector
16. Plug
17. Pinion shaft
18. Pinion gear
: Apply Genuine Silicone RTV or an equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
Refer to
for symbols not described on the above.
JPDIC0437GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст