Nissan Cube. Instruction — part 89
BRC-6
< BASIC INSPECTION >
[VDC/TCS/ABS]
DIAGNOSIS AND REPAIR WORKFLOW
2.
PERFORM THE SELF-DIAGNOSIS
Perform self-diagnosis for “ABS” with CONSULT.
Is there any DTC displayed?
YES
>> Record or print self-diagnosis results and freeze frame data (FFD). GO TO 3.
NO
>> GO TO 4.
3.
PERFORM THE SYSTEM DIAGNOSIS
Perform the diagnosis applicable to the displayed DTC for “ABS” with CONSULT. Refer to
.
>> GO TO 7.
4.
CHECK THE SYMPTOM THAT IS NOT CONSIDERED A SYSTEM MALFUNCTION
Check that the symptom is a normal operation that is not considered a system malfunction. Refer to
Is the symptom a normal operation?
YES
>> INSPECTION END
NO
>> GO TO 5.
5.
CHECK THE WARNING LAMP AND INDICATOR LAMP FOR ILLUMINATION
Check that the warning lamp and indicator lamp illuminate.
• ABS warning lamp: refer to
.
• Brake warning lamp: refer to
• VDC OFF indicator lamp: refer to
.
• VDC warning lamp: refer to
Is ON/OFF timing normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
6.
PERFORM THE DIAGNOSIS BY SYMPTOM
Perform the diagnosis applicable to the symptom for “ABS” with CONSULT.
>> GO TO 7.
7.
REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 8.
8.
MEMORY CLEAR
Perform self-diagnosis memory clear for “ABS” with CONSULT.
>> GO TO 9.
9.
FINAL CHECK
Perform the self-diagnosis again, and check that the malfunction is repaired completely.
Is no other DTC present and the repair completed?
YES
>> INSPECTION END
NO
>> GO TO 3.
DIAGNOSIS AND REPAIR WORKFLOW
BRC-7
< BASIC INSPECTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Diagnostic Work Sheet
INFOID:0000000009949897
SFIA3265E
BRC-8
< BASIC INSPECTION >
[VDC/TCS/ABS]
ADDITIONAL SERVICE WHEN REPLACING ABS ACTUATOR AND ELECTRIC
UNIT (CONTROL UNIT)
ADDITIONAL SERVICE WHEN REPLACING ABS ACTUATOR AND ELEC-
TRIC UNIT (CONTROL UNIT)
Description
INFOID:0000000009949898
After replacing the ABS actuator and electric unit (control unit), perform the neutral position adjustment for the
steering angle sensor.
Special Repair Requirement
INFOID:0000000009949899
1.
PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
Perform the neutral position adjustment for the steering angle sensor.
>> Refer to
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
BRC-9
< BASIC INSPECTION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Description
INFOID:0000000009949900
When doing work that applies to the list below, make sure to adjust neutral position of steering angle sensor
before running vehicle.
×
: Required –: Not required
Special Repair Requirement
INFOID:0000000009949901
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
CAUTION:
To adjust neutral position of steering angle sensor, make sure to use CONSULT.
(Adjustment cannot be done without CONSULT.)
1.
ALIGN THE VEHICLE STATUS
Stop vehicle with front wheels in straight-ahead position.
>> GO TO 2.
2.
PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR
1.
Select “ABS”, “WORK SUPPORT” and “ST ANGLE SENSOR ADJUSTMENT” in order with CONSULT.
2.
Select “START”.
CAUTION:
Never touch steering wheel while adjusting steering angle sensor.
3.
After approximately 10 seconds, select “END”.
NOTE:
After approximately 60 seconds, it ends automatically.
4.
Turn the ignition switch OFF, then turn it ON again.
CAUTION:
Be sure to perform above operation.
>> GO TO 3.
3.
CHECK DATA MONITOR
1.
Run the vehicle with front wheels in straight-ahead position, then stop.
2.
Select “ABS”, DATA MONITOR” and “STR ANGLE SIG” in order with CONSULT, and check steering
angle sensor signal.
Is the steering angle within the specified range?
Situation
Adjustment of steering angle sensor neutral position
Removing/Installing ABS actuator and electric unit (control unit)
—
Replacing ABS actuator and electric unit (control unit)
×
Removing/Installing steering angle sensor
×
Replacing steering angle sensor
×
Removing/Installing steering components
×
Replacing steering components
×
Removing/Installing suspension components
×
Replacing suspension components
×
Removing/Installing tire
—
Change tires to new ones
—
Tire rotation
—
Adjusting wheel alignment
×
STR ANGLE SIG
: 0
±
2.5
°
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст