Nissan Cube. Instruction — part 661
MA-18
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
3.
Screw oil filter instructionly until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to specification.
OIL FILTER : Inspection
INFOID:0000000009949429
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level. Refer to
.
2.
Start the engine, and check that there is no leakage of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check the engine oil level, and adjust the level. Refer to
.
SPARK PLUG
SPARK PLUG : Removal and Installation
INFOID:0000000010269295
REMOVAL
1.
Remove ignition coil. Refer to
.
2.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
CAUTION:
Never drop or shock spark plug.
INSTALLATION
Install in the reverse order of removal.
SPARK PLUG : Inspection
INFOID:0000000010269296
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
a
: 14 mm (0.55 in)
JPBIA0030ZZ
Spark plug (Standard type)
: Refer to
ENGINE MAINTENANCE
MA-19
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
• Never drop or shock spark plug.
• Never use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
• Spark plug gap adjustment is not required between replace-
ment intervals.
• Measure spark plug gap. when it exceeds the limit, replace
spark plug even if it is with in the specified replacement mile-
age. Refer to
.
EVAP VAPOR LINES
EVAP VAPOR LINES : Inspection
INFOID:0000000009949432
1.
Visually inspect EVAP vapor lines for improper attachment and for cracks, damage, loose connections,
chafing and deterioration. Refer to
.
2.
Inspect fuel tank filler cap vacuum relief valve for clogging, sticking, etc.
Refer to
EC-296, "Component Inspection"
Cleaner air pressure
: Less than 588 kPa (6 kg/cm
2
,
85 psi)
Cleaning time
: Less than 20 seconds
SMA773C
JPBIA0031ZZ
MA-20
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
CHASSIS MAINTENANCE
EXHAUST SYSTEM
EXHAUST SYSTEM : Inspection
INFOID:0000000009949433
Check exhaust pipes, muffler, and mounting for improper attach-
ment, leakage, cracks, damage or deterioration.
• If anything is found, repair or replace damaged parts.
CVT FLUID
CVT FLUID : Inspection
INFOID:0000000010269324
Level check
Check fluid level in HOT state [CVT fluid temperature is between 50 to 80
°
C (122 to 176
°
F)], according to the
following procedures.
1.
Visually check that CVT fluid leakage from transaxle assembly is not detected.
2.
After engine warms up, drive the vehicle in an urban area for approximately 10 minutes.
NOTE:
When ambient temperature is 20
°
C (68
°
F), driving vehicle for approximately 10 minutes in an urban area
ordinarily warms up CVT fluid temperature between 50 to 80
°
C (122 to 176
°
F).
3.
Park the vehicle on a level surface.
4.
Fully apply parking brake.
5.
Adjust engine speed at idle state.
6.
Shift selector lever through entire position from “P” to “D” while depressing brake pedal.
7.
Press claw of CVT fluid level gauge lock to unlock.
8.
Remove CVT fluid level gauge from CVT fluid charging pipe.
9.
Wipe CVT fluid that is on CVT fluid level gauge.
CAUTION:
Always use shop paper when wiping off CVT fluid that is on
CVT fluid level gauge.
10. Rotate CVT fluid level gauge 180
°
from installed state.
11. Inset CVT fluid level gauge until it contacts CVT fluid charging
pipe end.
12. Check that CVT fluid level is within the specified level of CVT fluid level gauge (MAX side).
SMA211A
SCIA1933E
SCIA1931E
CHASSIS MAINTENANCE
MA-21
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
CAUTION:
• After level check, when returning CVT fluid level gauge to the original state, insert CVT fluid level
gauge to CVT fluid charging pipe until it is locked.
• Always use shop paper when wiping off CVT fluid that is on CVT fluid level gauge.
CVT FLUID CONDITION
Check CVT fluid condition.
• If CVT fluid is very dark or smells burned, check operation of tran-
saxle assembly. Flush cooling system after repair of transaxle
assembly.
• If CVT fluid contains frictional material (clutches, brakes, etc.),
replace radiator and flush cooler line using cleaning solvent and
compressed air after repair of transaxle assembly. Refer to
231, "CVT FLUID COOLER HOSE : Exploded View"
.
CVT FLUID : Changing
INFOID:0000000010269325
1.
Remove drain plug from oil pan and then the CVT fluid.
2.
Remove drain plug gasket from drain plug.
3.
Install drain plug gasket to drain plug.
CAUTION:
Never reuse drain plug gasket.
4.
Install drain plug to oil pan.
5.
Fill CVT fluid from CVT fluid charging pipe to the specified level.
CAUTION:
• Always use the specified fluid. If use, misuse, or mixing of fluid other than the specified fluid
occurs, original performance cannot be obtained or it may cause serious malfunctions.
• CVT fluid is not reusable. Never reuse CVT fluid.
• Always use shop paper. Never use shop cloth.
• After replacement, always perform CVT fluid leakage check.
• Delete CVT fluid deterioration date with CONSULT after changing CVT fluid.
6.
After engine warms up, drive the vehicle in an urban area for approximately 10 minutes.
NOTE:
When ambient temperature is 20
°
C (68
°
F), it takes about 10 minutes for the CVT fluid to warm up to 50 to
80
°
C (122 to 176
°
F).
7.
Check CVT fluid level and condition. Refer to
MA-20, "CVT FLUID : Inspection"
8.
Repeat steps 1 to 6 if CVT fluid has been contaminated.
GEAR OIL
Fluid status
Conceivable cause
Required operation
Varnished (viscous
varnish state)
CVT fluid become
degraded due to
high temperatures
• Replace the CVT fluid.
• Check the transaxle assembly
and the vehicle for malfunctions
(wire harnesses, cooler pipes,
etc.)
Milky white or
cloudy
Water in the fluid
• Replace the CVT fluid.
• Check for places where water is
getting in.
Large amount of
metal powder mixed
in
Unusual wear of
sliding parts within
transaxle assembly
• Replace the CVT fluid.
• Check for improper operation of
the transaxle assembly.
ATA0022D
CVT fluid and fluid capacity
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст