Nissan Cube. Instruction — part 660
MA-14
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
6.
Refill reservoir tank to “MAX” level line with engine coolant.
7.
Install air duct (between air cleaner case and electric throttle control actuator). Refer to
.
8.
Install radiator cap.
9.
Warm up engine until opening thermostat. Standard for warming-up time is approximately 10 minutes at
3,000 rpm.
• Check thermostat opening condition by touching radiator hose (lower) to see a flow of warm water.
CAUTION:
Watch water temperature gauge so as not to overheat engine.
10. Stop the engine and cool down to less than approximately 50
°
C (122
°
F).
• Cool down using fan to reduce the time.
• If necessary, refill radiator up to filler neck with engine coolant.
CAUTION:
Never adhere the engine coolant to electronic equipments (alternator etc.).
11. Refill reservoir tank to “MAX” level line with engine coolant.
12. Repeat steps 5 through 10 two or more times with radiator cap installed until engine coolant level no
longer drops.
13. Check cooling system for leakage with engine running.
14. Warm up the engine, and check for sound of engine coolant flow while running engine from idle up to
3,000 rpm with heater temperature controller set at several position between “COOL” and “WARM”.
• Sound may be noticeable at heater unit.
15. Repeat step 14 three times.
16. If sound is heard, bleed air from cooling system by repeating step 5 through 10 until reservoir tank level no
longer drops.
ENGINE COOLANT : Flushing
INFOID:0000000009949423
1.
Install reservoir tank if removed and radiator drain plug.
CAUTION:
Be sure to clean drain plug and install with new O-ring.
• If water drain plugs on cylinder block are removed, close and tighten them. Refer to
.
2.
Remove air duct (between air cleaner case and electric throttle control actuator). Refer to
Engine coolant capacity
(With reservoir tank at “MAX” level)
Refer to
CO-25, "Periodical Maintenance Specifica-
.
A
: MAX
B
: MIN
Reservoir tank engine coolant capacity
(At “MAX” level)
Refer to
CO-25, "Periodical Maintenance Specification"
JPBIA0102ZZ
Radiator drain plug
: Refer to
ENGINE MAINTENANCE
MA-15
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
3.
Disconnect heater hose (1) at position (
) in the figure.
• Enhance heater as high as possible.
4.
Fill radiator and reservoir tank with water and reinstall radiator cap.
• When engine coolant over flows disconnected heater hose, connect heater hose, and continue filling the
engine coolant.
5.
Install air duct (between air cleaner case and electric throttle control actuator). Refer to
.
6.
Run the engine and warm it up to normal operating temperature.
7.
Rev the engine two or three times under no-load.
8.
Stop the engine and wait until it cools down.
9.
Drain water from the system. Refer to
MA-12, "ENGINE COOLANT : Draining"
.
10. Repeat steps 1 through 9 until clear water begins to drain from radiator.
FUEL LINES
FUEL LINES : Inspection
INFOID:0000000009949424
Inspect fuel lines, fuel filler cap, and fuel tank for improper attach-
ment, leakage, cracks, damage, loose connections, chafing or dete-
rioration.
If necessary, repair or replace damaged parts.
AIR CLEANER FILTER
AIR CLEANER FILTER : Removal and Installation
INFOID:0000000009949425
REMOVAL
1.
Push the tabs (A) of both ends of the air cleaner cover (1) into
the inside (B).
2.
Pull up the air cleaner cover forward (C) and remove it.
: Vehicle front
PBIC3802E
A
: Engine
B
: Fuel line
C
: Fuel tank
JPBIA0129ZZ
PBIC3557J
MA-16
< PERIODIC MAINTENANCE >
ENGINE MAINTENANCE
3.
Remove the air cleaner filter (1) and holder (2) assembly from
the air cleaner case.
4.
Remove the air cleaner filter from the holder.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the air cleaner cover (1) in the direction as shown in the fig-
ure.
AIR CLEANER FILTER : Inspection (Viscous Paper Type)
INFOID:0000000010210178
INSPECTION AFTER REMOVAL
Examine with eyes that there is no stain, clogging, or damage on air cleaner element.
• Remove dusts (such as dead leafs) on air cleaner element surface and inside cleaner case.
• If clogging or damage is observed, replace the air cleaner element.
CAUTION:
Never clean the viscous paper type air cleaner element by blowing as there is a risk of deterioration of
its performance
MAINTENANCE INTERVAL
MA-6, "Introduction of Periodic Maintenance"
ENGINE OIL
ENGINE OIL : Draining
INFOID:0000000009949426
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1.
Warm up the engine, and check for engine oil leakage from engine components. Refer to
2.
Stop the engine and wait for 10 minutes.
3.
Loosen oil filler cap.
4.
Remove drain plug and then drain engine oil.
ENGINE OIL : Refilling
INFOID:0000000009949427
1.
Install drain plug with new drain plug washer. Refer to
CAUTION:
Be sure to clean drain plug and install with new drain plug washer.
PBIC3558J
2
: Air cleaner filter
3
: Holder
PBIC3559J
ENGINE MAINTENANCE
MA-17
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
2.
Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-10, "Fluids and Lubricants"
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3.
Warm up engine and check area around drain plug and oil filter for engine oil leakage.
4.
Stop engine and wait for 10 minutes.
5.
Check the engine oil level. Refer to
.
OIL FILTER
OIL FILTER : Removal and Installation
INFOID:0000000009949428
REMOVAL
1.
Remove engine under cover. Refer to
.
2.
Using oil filter wrench [SST: KV10115801 (J-38956)] (A), remove
oil filter.
CAUTION:
• Oil filter is provided with relief valve. Use genuine NISSAN
oil filter or equivalent.
• Be careful not to get burned when engine and engine oil
may be hot.
• When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1.
Remove foreign materials adhering to the oil filter installation surface.
2.
Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
Tightening torque
: Refer to
.
Engine oil capacity
: Refer to
LU-15, "Periodical Maintenance Specification"
: Vehicle front
PBIC3312J
SMA010
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст