Nissan Cube. Instruction — part 60
BCS
COMBINATION SWITCH
BCS-89
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMBINATION SWITCH
Exploded View
INFOID:0000000009949747
Removal and Installation
INFOID:0000000009949748
REMOVAL
1.
Remove steering column cover. Refer to
.
2.
Remove screws.
3.
Disconnect the connector.
4.
Pull up the combination switch to remove it.
INSTALLATION
Install in the reverse order of removal.
1.
Combination switch
2.
Combination switch connector
JPMIA1517ZZ
BCS-90
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
BASIC INSPECTION
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
Description
INFOID:0000000009949749
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-
ment.
NOTE:
If “READ CONFIGURATION” cannot be used, use the “WRITE CONFIGURATION - Instruction selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
NOTE:
• When replacing BCM, perform the system initialization (NATS) (if equipped).
• When replacing BCM, perform the keyfob ID registration (if equipped).
Work Procedure
INFOID:0000000009949750
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to
.
NOTE:
If “READ CONFIGURATION” cannot be used, use the “WRITE CONFIGURATION - Instruction selection” after
replacing BCM.
>> GO TO 2.
2.
REPLACE BCM
Replace BCM. Refer to
BCS-155, "Removal and Installation"
.
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Instruction selection” to write
vehicle specification. Refer to
>> GO TO 4.
4.
INITIALIZE BCM (NATS) (IF EQUIPPED)
Perform BCM initialization. (NATS)
>> GO TO 5.
5.
KEYFOB ID REGISTRATION (IF EQUIPPED)
Perform keyfob ID registration. Refer to
DLK-234, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
.
>> WORK END
BCS
CONFIGURATION (BCM)
BCS-91
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CONFIGURATION (BCM)
Description
INFOID:0000000009949751
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows.
NOTE:
Instruction setting item: Items which need selection by vehicle specifications
Automatic setting item: Items which are written in automatically (Setting cannot be changed)
For some models and specifications, the automatic setting item may not be displayed.
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• Never perform “WRITE CONFIGURATION” except for new BCM.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
Work Procedure
INFOID:0000000009949752
1.
WRITING MODE SELECTION
CONSULT Configuration
Select “CONFIGURATION” of BCM.
When writing saved data>>GO TO 2.
When writing instructionly>>GO TO 3.
2.
PERFORM “WRITE CONFIGURATION - CONFIG FILE”
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file”.
>> WORK END
3.
PERFORM “WRITE CONFIGURATION - MANUAL SELECTION”
CONSULT Configuration
1.
Select "WRITE CONFIGURATION - Instruction selection".
2.
Identify the correct model and configuration list. Refer to
.
3.
Confirm and/or change setting value for each item.
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally
if the setting is not correct.
NOTE:
If items are not displayed, touch “SETTING”. Refer to
for written items and
setting value.
4.
Select "SETTING".
CAUTION:
Make sure to select “SETTING” even if the indicated configuration of brand new BCM is same as
the desirable configuration. If not, configuration which is set automatically by selecting vehicle
model cannot be memorized.
5.
When "COMMAND FINISHED", select "END".
Function
Description
READ CONFIGURATION
• Reads the vehicle configuration of current BCM.
• Saves the read vehicle configuration.
WRITE CONFIGURATION - Instruction selection
Writes the vehicle configuration with instruction selection.
WRITE CONFIGURATION - Config file
Writes the vehicle configuration with saved data.
BCS-92
< BASIC INSPECTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
CONFIGURATION (BCM)
>> GO TO 4.
4.
OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> WORK END
Configuration list
INFOID:0000000009949753
CAUTION:
Thoroughly read and understand the vehicle specification. ECU control may not operate normally if
the setting is not correct.
⇔
: Items which confirm vehicle specifications
SETTING ITEM
NOTE
Items
Setting value
CAN FAULT DETECTION
MODE4
⇔
WITHOUT
• MODE4: Except M/T models
• WITHOUT: M/T models
AUTO LIGHT
WITHOUT
—
DTRL
WITH
⇔
WITHOUT
• WITH: With daytime running light system
• WITHOUT: Without daytime running light system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст