Nissan Cube. Instruction — part 112
BRC-98
< ECU DIAGNOSIS INFORMATION >
[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
DTC Index
INFOID:0000000009950029
DTC
Items (CONSULT screen terms)
Reference
C1101
RR RH SENSOR-1
C1102
RR LH SENSOR-1
C1103
FR RH SENSOR-1
C1104
FR LH SENSOR-1
C1105
RR RH SENSOR-2
C1106
RR LH SENSOR-2
C1107
FR RH SENSOR-2
C1108
FR LH SENSOR-2
C1109
BATTERY VOLTAGE [ABNORMAL]
C1110
CONTROLLER FAILURE
C1111
PUMP MOTOR
C1115
ABS SENSOR [ABNORMAL SIGNAL]
C1116
STOP LAMP SW
C1120
FR LH IN ABS SOL
C1121
FR LH OUT ABS SOL
C1122
FR RH IN ABS SOL
C1123
FR RH OUT ABS SOL
C1124
RR LH IN ABS SOL
C1125
RR LH OUT ABS SOL
C1126
RR RH IN ABS SOL
C1127
RR RH OUT ABS SOL
C1130
ENGINE SIGNAL 1
C1140
ACTUATOR RLY
C1142
PRESS SEN CIRCUIT
C1143
ST ANG SEN CIRCUIT
C1144
ST ANG SEN SIGNAL
C1145
YAW RATE SENSOR
C1146
SIDE G-SEN CIRCUIT
C1153
EMERGENCY BRAKE
C1155
BR FLUID LEVEL LOW
C1164
CV 1
C1165
CV 2
C1166
SV 1
C1167
SV 2
C1170
VARIANT CORDING
U1000
CAN COMM CIRCUIT
U1002
SYSTEM COMM
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
BRC-99
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SYMPTOM DIAGNOSIS
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis Procedure
INFOID:0000000009950030
1.
CHECK START
Check front and rear brake force distribution using a brake tester. Refer to
BR-43, "General Specifications"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check brake system.
2.
CHECK FRONT AND REAR AXLE
Make sure that there is no excessive play in the front and rear axles.
• Front: refer to
• Rear: refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK WHEEL SENSOR AND SENSOR ROTOR
Check the following.
• Wheel sensor installation for damage.
• Wheel sensor harness connector connection.
• Wheel sensor harness inspection.
• Sensor rotor installation for damage.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>>
Replace wheel sensor or sensor rotor.
• Front wheel sensor: refer to
BRC-110, "FRONT WHEEL SENSOR : Exploded View"
.
• Rear wheel sensor: refer to
BRC-111, "REAR WHEEL SENSOR : Exploded View"
• Front sensor rotor: refer to
BRC-112, "FRONT SENSOR ROTOR : Removal and Installation"
.
• Rear sensor rotor: refer to
BRC-112, "REAR SENSOR ROTOR : Removal and Installation"
.
4.
CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp is turned OFF for approximately 1 second after the ignition switch is
turned ON or when driving.
Is the inspection result normal?
YES
>> Normal
NO
>> Perform self-diagnosis for “ABS” with CONSULT.
BRC-100
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
UNEXPECTED PEDAL REACTION
UNEXPECTED PEDAL REACTION
Diagnosis Procedure
INFOID:0000000009950031
1.
CHECK BRAKE PEDAL STROKE
Check brake pedal stroke. Refer to
BR-7, "Inspection and Adjustment"
Is the stroke too large?
YES
>> • Bleed air from brake tube and hose. Refer to
BR-11, "Bleeding Brake System"
• Check brake fluid leakage. Refer to
• Check brake pedal, brake booster, and master cylinder for mount play, looseness, etc.
- Brake pedal: refer to
BR-18, "Inspection and Adjustment"
.
- Brake master cylinder: refer to
- Brake booster: refer to
BR-29, "Inspection and Adjustment"
- Front disc brake: refer to
BR-38, "BRAKE CALIPER ASSEMBLY : Inspection"
.
- Rear drum brake: refer to
BR-41, "Inspection and Adjustment"
.
NO
>> GO TO 2.
2.
CHECK FUNCTION
1.
Turn the ignition switch OFF.
2.
Disconnect ABS actuator and electric unit (control unit) harness connector to deactivate ABS. Check if
braking force is normal in this condition. Connect harness connector after inspection.
Is the inspection result normal?
YES
>> Normal
NO
>> Check brake system.
THE BRAKING DISTANCE IS LONG
BRC-101
< SYMPTOM DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
THE BRAKING DISTANCE IS LONG
Diagnosis Procedure
INFOID:0000000009950032
CAUTION:
The stopping distance on slippery road surfaces might be longer when the ABS is operating than
when the ABS is not operating.
1.
CHECK FUNCTION
1.
Turn the ignition switch OFF
2.
Disconnect ABS actuator and electric unit (control unit) harness connector to deactivate ABS. In this con-
dition, check stopping distance. After inspection, connect harness connector.
Is the inspection result normal?
YES
>> Normal
NO
>> Check brake system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст