Nissan Cube. Instruction — part 246
DLK-250
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR SWITCH
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between door switch harness connector and BCM harness connector.
(+)
(–)
Signal
(Reference value)
Door switch
Connector
Terminal
Driver side
B34
3
Ground
7.0 - 8.0 V
Passenger side
B27
3
7.0 - 8.0 V
Rear LH
B71
3
7.0 - 8.0 V
Rear RH
B53
3
7.0 - 8.0 V
Back door
B75
3
9.5 - 10.0 V
PKIB4960J
PKIB4960J
PKIB4960J
PKIB4960J
PKIB4960J
DOOR SWITCH
DLK-251
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between door switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-155, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR SWITCH
DLK-251, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunctioning door switch. Refer to
DLK-378, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009950692
1.
CHECK DOOR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect malfunctioning door switch connector.
3.
Check continuity between door switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace malfunction door switch. Refer to
DLK-378, "Removal and Installation"
Door switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
Driver side
B34
3
M66
47
Existed
Passenger side
B27
M65
12
Rear LH
B71
M66
48
Rear RH
B53
M65
13
Back door
B75
M66
43
Door switch
Ground
Continuity
Connector
Terminal
Driver side
B34
3
Not existed
Passenger side
B27
Rear LH
B71
Rear RH
B53
Back door
B75
Door switch
Condition
Continuity
Terminal
3
Ground part of door switch
Door switch
Pressed
Not existed
Released
Existed
DLK-252
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000009950693
Transmits door lock/unlock operation to BCM.
DRIVER SIDE : Component Function Check
INFOID:0000000009950694
1.
CHECK FUNCTION
Check “CDL LOCK SW ”and “CDL UNLOCK SW” in BCM “Data Monitor” mode using CONSULT.
Is the inspection result normal?
YES
>> Door lock and unlock switch is OK.
NO
>> Refer to
DLK-252, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000009950695
1.
CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check signal between power window main switch harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT
1.
Disconnect BCM connector and front power window switch (passenger side) connector.
2.
Check continuity between BCM harness connector and power window main switch harness connector.
3.
Check continuity between BCM harness connector and ground.
Monitor item
Condition
Status
CDL LOCK SW
Door lock and unlock switch
LOCK
ON
UNLOCK
OFF
CDL UNLOCK SW
LOCK
OFF
UNLOCK
ON
(+)
(–)
Signal
(Reference value)
Power window main switch
Connector
Terminal
D5
6
Ground
1.0 - 1.5 V
18
JPMIA0012GB
BCM
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
M66
45
D5
18
Existed
46
6
DOOR LOCK AND UNLOCK SWITCH
DLK-253
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace BCM. Refer to
BCS-155, "Removal and Installation"
.
4.
CHECK DOOR LOCK AND UNLOCK SWITCH GROUND
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK DOOR LOCK AND UNLOCK SWITCH
DLK-253, "DRIVER SIDE : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace power window main switch. Refer to
PWC-112, "Removal and Installation"
.
6.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
DRIVER SIDE : Component Inspection
INFOID:0000000009950696
1.
CHECK DOOR LOCK AND UNLOCK SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch (door lock and unlock switch) connector.
BCM
Ground
Continuity
Connector
Terminal
M66
45
Not existed
46
(+)
(–)
Signal
(Reference value)
BCM
Connector
Terminal
M66
45
Ground
1.0 - 1.5 V
46
JPMIA0012GB
Power window main switch
Ground
Continuity
Connector
Terminal
D6
17
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст