Nissan Cube. Instruction — part 982
TM-184
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F08B]
TCM
Fail-safe
INFOID:0000000009949057
Description
When a malfunction is detected in each sensor, switch, solenoid or others, this function provides control to
minimize reduction of drivability so that durability of transmission assembly can be acquired.
JRDWC1937GB
TCM
TM-185
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DTC
Condition
Vehicle behavior
P0703
—
• Start is slow
• Acceleration is slow
P0705
—
• Position indicator on combination meter is not dis-
played
• Selector shock is large
• Start is slow
• Acceleration at high load state is slow
• Overdrive off condition is not activated
• “L” position is not activated
P0710
Engine coolant temperature
when engine starts is 10
°
C
(50
°
F) or more
Open circuit is detected while ig-
nition switch is OFF
• Selector shock is large
• Low is fixed
Other than the above
• Selector shock is large
• Engine speed is high in middle and high speed
range
Engine coolant temperature when engine starts is 10
°
C (50
°
F) or
less
• Start is slow
• Acceleration is slow
• Vehicle speed is not increased
Engine coolant temperature when engine starts is
−
35
°
C (
−
31
°
F)
or less
Vehicle speed is not increased
P0715
—
• Re-acceleration is slightly slow
• Re-start is slow after vehicle is stop by strong decel-
eration
• Overdrive off condition is not activated
• “L” position is not activated
• Lock-up is not performed
P0720
—
• Start is slow
• Re-acceleration is slow
• Re-start is slow after vehicle is stop by strong decel-
eration
• Overdrive off condition is not activated
• “L” position is not activated
• Lock-up is not performed
P0725
—
Lock-up is not performed
P0740
—
• Selector shock is large
• Lock-up is not performed
P0744
—
Lock-up is not performed
P0746
A malfunction is detected
• Start is slow
• Acceleration is slow
• Lock-up is not performed
Function is excessively reduced after a malfunction is detected
• Start is difficult
• Drive is difficult
• Lock-up is not performed
P0778
—
Engine speed is high in middle and high speed range
P0840
—
• Start is slow
• Acceleration at high load state is slow
P0841
—
• Start is slow
• Acceleration is slow
P0868
—
• Start is slow
• Acceleration is slow
(Slow acceleration is subject to secondary pressure
that is recognized by TCM)
P1701
—
• Start is slow
• Acceleration at high load state is slow
P1705
—
• Acceleration is slow
• Lock-up is not performed
TM-186
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F08B]
TCM
DTC Inspection Priority Chart
INFOID:0000000009949058
If some DTCs are displayed at the same time, perform inspections one by one based on the priority as per the
following list.
DTC Index
INFOID:0000000009949059
When multiple malfunctions are detected simultaneously, perform inspection one by one according to DTC
check priority list. Refer to
TM-186, "DTC Inspection Priority Chart"
.
P1709
—
• Start is slow
• Acceleration is slow
• Shift position indicator (P, N) is not displayed, or is
displayed with delay
P1722
—
Lock-up is not activated in coast state
P1723
A malfunction is detected in primary pulley speed sensor side
• Acceleration is slow
• Re-start is slow after vehicle is stop by strong decel-
eration
• Overdrive off condition is not activated
• “L” position is not activated
• Lock-up is not performed
A malfunction is detected in secondary pulley speed sensor
• Start is slow
• Acceleration is slow
• Re-start is slow after vehicle is stop by strong decel-
eration
• Overdrive off condition is not activated
• “L” position is not activated
• Lock-up is not performed
P1726
—
Acceleration is slow
P1740
—
• Selector shock is large
• Lock-up is not performed
P1777
A malfunction is detected in low side (when vehicle is stopped)
• Low is fixed
• Lock-up is not performed
A malfunction is detected in high side (during driving)
• Start is slow
• Acceleration is low in low speed range
• Lock-up is not performed
U0100
—
• Start is slow
• Acceleration is slow
• Vehicle speed is not increased
U1000
—
• Start is slow
• Acceleration is slow
• Vehicle speed is not increased
U1010
—
• Start is slow
• Acceleration is slow
• Vehicle speed is not increased
DTC
Condition
Vehicle behavior
Priority
Detected items (DTC)
1
U0100, U1000, U1010, P1709
2
Except above
DTC
*1
Items
(CONSULT screen terms)
Reference
MIL
*2
, “ENGINE” with
CONSULT or GST
“TRANSMISSION” with
CONSULT
U0100
U0100
LOST COMM (ECM A)
U1000
U1000
CAN COMM CIRCUIT
—
U1010
CONTROL UNIT (CAN)
TCM
TM-187
< ECU DIAGNOSIS INFORMATION >
[CVT: RE0F08B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
*1: These numbers are prescribed by SAE J2012.
*2: Refer to
TM-98, "Diagnosis Description"
—
P0703
BRAKE SWITCH B
P0705
P0705
T/M RANGE SENSOR A
P0710
P0710
FLUID TEMP SENSOR A
P0715
P0715
INPUT SPEED SENSOR A
P0720
P0720
OUTPUT SPEED SENSOR
—
P0725
ENGINE SPEED
P0740
P0740
TORQUE CONVERTER
P0744
P0744
TORQUE CONVERTER
P0745
P0745
PC SOLENOID A
P0746
P0746
PC SOLENOID A
P0776
P0776
PC SOLENOID B
P0778
P0778
PC SOLENOID B
P0840
P0840
FLUID PRESS SEN/SW A
—
P0841
FLUID PRESS SEN/SW A
—
P0868
FLUID PRESS LOW
—
P1701
TCM
—
P1705
TP SENSOR
—
P1709
INCOMPLETED DATA WRITING
—
P1722
VEHICLE SPEED
—
P1723
SPEED SENSOR
—
P1726
THROTTLE CONTROL SIGNAL
P1740
P1740
SLCT SOLENOID
P1777
P1777
STEP MOTOR
P1778
P1778
STEP MOTOR
DTC
*1
Items
(CONSULT screen terms)
Reference
MIL
*2
, “ENGINE” with
CONSULT or GST
“TRANSMISSION” with
CONSULT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст