Nissan March K13. Instruction — part 610
SR-18
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
• The spiral cable may snap during steering operation if the
cable is installed in an improper position.
The neutral position is set as follows.
• Carefully turn the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and a half turns) and
stop turning at the mark (B) on which the stopper insertion
holes are in the same position.
• The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper is
removed.
• Never over turn the spiral cable or go beyond the number of
turns required. (This will cause the cable to snap)
• Adjust the spiral cable locating pin (A) to the steering wheel
locating pin hole (C).
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0879ZZ
FRONT PASSENGER AIR BAG MODULE
SR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000006044242
Removal and Installation
INFOID:0000000006044243
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove glove box escutcheon (without glove box lid). Refer to
IP-13, "Removal and Installation"
2.
Remove the cluster lid C, instrument finisher B, and glove box cover (without glove upper box). Refer to
IP-13, "Removal and Installation"
.
3.
Remove the glove upper box and glove box cover (with glove upper box). Refer to
.
1.
Passenger air bag module
2.
Instrument panel assembly
: Pawl
Refer to
JMHIA1529GB
SR-20
< REMOVAL AND INSTALLATION >
FRONT PASSENGER AIR BAG MODULE
4.
Disconnect the front passenger air bag module harness connec-
tor (A) from front passenger air bag module.
5.
Remove the front passenger air bag module fixing bolts (B).
6.
Disengage front passenger air bag module fixing pawls with
hands.
CAUTION:
Never insert a remover tool between passenger air bag
module and instrument panel assembly. Doing so may
cause damage.
CAUTION:
• Always place the front passenger air bag module with pad
side facing upward.
• Never impact the front passenger air bag module.
• Replace the front passenger air bag module if it has been
dropped or sustained an impact.
• Never insert any foreign objects (screwdriver, etc.) into the front passenger air bag module.
• Never disassemble the front passenger air bag module.
• Never expose the front passenger air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the front passenger air bag mod-
ule.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal, replace with the new bolts.
• Never damage the harness while installing.
JMHIA1530ZZ
: Pawl
JMHIA1531ZZ
: Upward
JMHIA1532ZZ
JMHIA0009ZZ
FRONT PASSENGER AIR BAG MODULE
SR-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст