Nissan March K13. Instruction — part 284
EM-70
< REMOVAL AND INSTALLATION >
[HR12DE]
OIL SEAL
FRONT OIL SEAL : Removal and Installation
INFOID:0000000005988199
REMOVAL
1.
Remove the following parts.
• Front fender protector (RH): Refer to
EXT-17, "FENDER PROTECTOR : Exploded View"
.
• Drive belt: Refer to
EM-19, "Removal and Installation"
• Crankshaft pulley: Refer to
.
2.
Remove front oil seal with a suitable tool.
CAUTION:
Be careful not to damage front cover and crankshaft.
INSTALLATION
1.
Apply new engine oil to new front oil seal joint surface and seal lip.
2.
Install front oil seal so that each seal lip is oriented as shown in
the figure.
• Press-fit front oil seal using a suitable drift with outer diameter 50 mm (1.97 in) and inner diameter 44
mm (1.73 in).
CAUTION:
• Be careful not to damage front cover and crankshaft.
• Press-fit oil seal straight to avoid causing burrs or tilting.
3.
Install in the reverse order of removal, for the rest of parts.
REAR OIL SEAL
REAR OIL SEAL : Removal and Installation
INFOID:0000000005988200
REMOVAL
1.
Remove transaxle assembly. Refer to
TM-19, "Removal and Installation"
(M/T models).
2.
Remove clutch cover and clutch disk (M/T models). Refer to
CL-17, "Removal and Installation"
3.
Remove flywheel (M/T models). Refer to
.
4.
Remove rear oil seal with a suitable tool.
CAUTION:
Be careful not to damage crankshaft and cylinder block.
INSTALLATION
1.
Apply the liquid gasket lightly to entire outside area of new rear oil seal.
Use Genuine Liquid Gasket or equivalent.
A
: Dust seal lip
B
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
OIL SEAL
EM-71
< REMOVAL AND INSTALLATION >
[HR12DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Install rear oil seal so that each seal lip is oriented as shown in
the figure.
• Press-fit rear oil seal with a suitable drift (A) outer diameter
113 mm (4.45 in) and inner diameter 90 mm (3.54 in).
CAUTION:
• Be careful not to damage crankshaft and cylinder block.
• Press-fit oil seal straight to avoid causing burrs or tilt-
ing.
• Never touch grease applied onto oil seal lip.
• Press in rear oil seal (1) to the position as shown in the figure.
3.
Install in the reverse order of removal, for the rest of parts.
A
: Dust seal lip
B
: Oil seal lip
: Engine outside
: Engine inside
PBIC3485J
PBIC3660E
A
: Rear end surface of cylinder block
b
: 0 - 0.5 mm (0 - 0.020 in)
JPBIA3011ZZ
EM-72
< REMOVAL AND INSTALLATION >
[HR12DE]
CYLINDER HEAD
CYLINDER HEAD
Exploded View
INFOID:0000000005988201
REMOVAL
DISASSEMBLY
1.
Cylinder head assembly
2.
Cylinder head bolt
3.
Washer
4.
Cylinder head gasket
A.
Tightening must be done following
the installation procedure.
Refer to
Refer to
for symbols in the figure.
JPBIA3392ZZ
JPBIA3393ZZ
CYLINDER HEAD
EM-73
< REMOVAL AND INSTALLATION >
[HR12DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Removal and Installation
INFOID:0000000005988202
REMOVAL
1.
Release fuel pressure. Refer to following;
• HR12DE (TYPE 1):
• HR12DE (TYPE 2):
2.
Drain engine coolant and engine oil. Refer to
.
CAUTION:
Perform this step when the engine is cold.
3.
Remove the following components and related parts.
• Front road wheel and tire (RH): Refer to
WT-4, "Removal and Installation"
• Front fender protector (RH): Refer to
EXT-17, "FENDER PROTECTOR : Exploded View"
.
• Drive belt: Refer to
EM-19, "Removal and Installation"
• Air duct: Refer to
• Intake manifold: Refer to
EM-29, "WITH EGR CONTROL VALVE : Exploded View"
.
• Fuel tube and fuel injector: Refer to
• Water outlet: Refer to
.
• Exhaust manifold: Refer to
.
• Rocker cover: Refer to
• Front cover and timing chain: Refer to
.
• Camshaft: Refer to
.
4.
Remove cylinder head loosening bolts in reverse order as
shown in the figure with cylinder head wrench (commercial ser-
vice tool).
5.
Remove cylinder head gasket.
INSTALLATION
1.
Install new cylinder head gasket.
1.
Spark plug
2.
Valve collet
3.
Valve spring retainer
4.
Valve spring
5.
Valve spring seat
6.
Valve oil seal
7.
Valve guide (EXH)
8.
Valve guide (INT)
9.
Cylinder head
10. Valve seat (EXH)
11. Valve (EXH)
12. Valve seat (INT)
13. Valve (INT)
A.
Replacement must be following the
disassembly and assembly proce-
dure.
Refer to
Refer to
for symbols in the figure.
A
: EXH side
B
: INT side
: Engine front
JPBIA3428ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст