Nissan March K13. Instruction — part 298
EXL-18
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000005969677
WORK SUPPORT
*1
: With remote keyless entry system models
*2
: Factory setting
DATA MONITOR
Service item
Setting
item
Setting
AUTO LIGHT LOGIC SET
*1
MODE 1
NOTE:
The item is displayed, but cannot be used
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
BATTERY SAVER SET
On
*2
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
ACC ON SW
[On/Off]
Ignition switch (ACC) status judged from ACC signal (ACC power supply)
VEH SPEED
[km/h]
The value of the vehicle speed received from combination meter with CAN commu-
nication
HI BEAM SW
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
FR FOG SW
[On/Off]
NOTE:
The item is indicated, but not monitored
AUTO LIGHT SW
*1
[On/Off]
NOTE:
The item is indicated, but not monitored
RR FOG SW
*1
[On/Off]
NOTE:
The item is indicated, but not monitored
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
BACK DOOR SW
[On/Off]
The switch status input from back door switch
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
EXL-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*1
: With remote keyless entry system models
*2
: Without power door lock system models do not displayed, Without remote keyless entry system models are
displayed but does not monitored.
ACTIVE TEST
*
: With remote keyless entry system models
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000005969678
DATA MONITOR
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
KEY ON SW
[On/Off]
The switch status input from key on switch
KEYLESS LOCK
*2
[On/Off]
Lock signal status received from remote keyless entry receiver (integrated in the
BCM)
PKB SW
[On/Off]
The parking brake switch status received from combination meter with CAN commu-
nication
ENGINE RUN
[On/Off]
The engine status received from ECM with CAN communication
OPTI SEN (DTCT)
*1
[V]
NOTE:
The item is indicated, but not monitored
OPTI SEN (FILT)
*1
[V]
NOTE:
The item is indicated, but not monitored
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
Off
Stops the tail lamp request signal transmission.
HEAD LAMP
Hi
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
Lo
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
Off
Stops the high & low beam request signal transmission.
ILL DIM SIGNAL
*
On
NOTE:
The item is indicated, but cannot be tested.
Off
FR FOG LAMP
On
NOTE:
The item is indicated, but cannot be tested.
Off
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Ignition switch (ON) status judged from IGN signal (ignition power supply)
EXL-20
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
ACTIVE TEST
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
Monitor item
[Unit]
Description
Test item
Operation
Description
FLASHER
RH
Outputs the voltage to blink the right side turn signal lamps.
LH
Outputs the voltage to blink the left side turn signal lamps.
Off
Stops the voltage to turn the turn signal lamps OFF.
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
EXL-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
Diagnosis Description
INFOID:0000000006046538
AUTO ACTIVE TEST
Description
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Front wiper (LO, HI)
• Parking lamps
• License plate lamps
• Tail lamps
• Front fog lamps
• Headlamps (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
CAUTION:
Never perform auto active test in the following conditions.
• Engine is running
• CONSULT-III is connected
1.
Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2.
Turn the ignition switch OFF.
3.
Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
4.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
CAUTION:
Engine starts when ignition switch is turned ON while brake pedal is depressed.
5.
The oil pressure warning lamp starts blinking when the auto active test starts.
6.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
XX-XX,
"*****"
.
Inspection in Auto Active Test
When auto active test is actuated, the following operation sequence is repeated 3 times.
Operation
sequence
Inspection location
Operation
1
Oil pressure warning lamp
Blinks continuously during operation of auto active test
2
Front wiper
LO for 5 seconds
→
HI for 5 seconds
3
• Parking lamps
• License plate lamps
• Tail lamps
• Front fog lamps
10 seconds
4
Headlamps
LO for 10 seconds
→
HI ON
⇔
OFF 5 times
5
A/C compressor (magnet clutch)
ON
⇔
OFF 5 times
6
Cooling fan
LO for 5 seconds
→
MID for 3 seconds
→
HI for 2 seconds
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст