Nissan March K13. Instruction — part 297
EXL-14
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
*: Factory setting
DATA MONITOR
Service item
Setting
item
Setting
AUTO LIGHT LOGIC SET
MODE 1
NOTE:
The item is indicated, but not operated.
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
CUSTOM A/LIGHT SETTING
MODE 1
*
NOTE:
The item is indicated, but not operated.
MODE 2
MODE 3
MODE 4
BATTERY SAVER SET
On
*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
The engine status received from ECM with CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from combination meter with CAN commu-
nication
HI BEAM SW
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
FR FOG SW
[On/Off]
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW-RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]
The switch status input from back door switch
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
EXL-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000005912298
WORK SUPPORT
*: Factory setting
DATA MONITOR
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON.
Off
Stops the tail lamp request signal transmission.
HEAD LAMP
Hi
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI).
Lo
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO).
Off
Stops the high & low beam request signal transmission.
FR FOG LAMP
On
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON.
Off
Stops the front fog lights request signal transmission.
ILL DIM SIGNAL
On
NOTE:
The item is indicated, but cannot be tested.
Off
Service item
Setting item
Setting
HAZARD ANSWER
BACK
Lock Only
With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the door request switch
and the Intelligent Key.
Unlk Only
With unlocking only
Lock/Unlk
*
With locking/unlocking
Off
Without the function
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from the request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from the request switch (passenger side)
PUSH SW
[On/Off]
The switch status input from the push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
EXL-16
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
ACTIVE TEST
HAZARD SW
[On/Off]
The switch status input from the hazard switch
RKE-LOCK
[On/Off]
Lock signal status received from the remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from the remote keyless entry receiver
RKE-PANIC
[On/Off]
Panic alarm signal status received from the remote keyless entry receiver
Monitor item
[Unit]
Description
Test item
Operation
Description
FLASHER
RH
Outputs the voltage to blink the right side turn signal lamps.
LH
Outputs the voltage to blink the left side turn signal lamps.
Off
Stops the voltage to turn the turn signal lamps OFF.
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
EXL-17
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000006046537
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
• *1: For models without NATS this mode is not used.
• *2: This item is displayed, but is not used.
HEADLAMP
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion instruction.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
• Automatic air conditioner
• Instruction air conditioner
AIR CONDITONER
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
*
1
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door
TRUNK
×
—
THEFT ALM*
2
×
×
—
RETAINED PWR*
2
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст