Nissan March K13. Instruction — part 459
MIR-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW
NOTE:
This item is indicated, but not monitored
BRAKE SW 1
Indicates [On/Off] condition of stop lamp switch
BRAKE SW 2
Indicates [On/Off]* condition of stop lamp switch power supply
DETE/CANCL SW
Indicates [On/Off] condition of P position
SFT PN/N SW
Indicates [On/Off] condition of P or N position
S/L -LOCK
Indicates [On/Off] condition of steering lock unit (LOCK)
S/L -UNLOCK
Indicates [On/Off] condition of steering lock unit (UNLOCK)
S/L RELAY -F/B
Indicates [On/Off] condition of steering lock relay
UNLK SEN -DR
Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
DETE SW -IPDM
Indicates [On/Off] condition of P position
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
SFT P -MET
Indicates [On/Off] condition of P position
SFT N -MET
Indicates [On/Off] condition of N position
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
S/L LOCK-IPDM
Indicates [On/Off] condition of steering lock unit (LOCK)
S/L UNLK-IPDM
Indicates [On/Off] condition of steering lock unit (UNLOCK)
S/L RELAY-REQ
Indicates [On/Off] condition of steering lock relay
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver side door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status
ID OK FLAG
Indicates [Set/Reset] condition of key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE:
This item is indicated, but not monitored
TRNK/HAT MNTR
NOTE:
This item is indicated, but not monitored
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is indicated, but not monitored
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is indicated, but not monitored
RKE-PANIC
Indicates [On/Off] condition of PANIC button of Intelligent Key
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
DIAGNOSIS SYSTEM (BCM)
MIR-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT-III screen is touched
• Key: Key warning chime sounds when CONSULT-III screen is touched
• Knob: OFF position warning chime sounds when CONSULT-III screen is touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT-III screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT-III screen is touched
• Off: Non-operation
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
LCD
This test is able to check meter display information
• B&P N: Engine start information indicate when CONSULT-III screen is touched
• B&P I: Engine start information indicate when CONSULT-III screen is touched
• ID NG: This item is displayed, but cannot be monitored
• ROTAT: This item is displayed, but cannot be monitored
• SFT P: Shift P warning lamp indicate when CONSULT-III screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: Key warning lamp indicator when CONSULT-III screen is touched
• NO KY: Key warning lamp indicator when CONSULT-III screen is touched
• OUTKEY: Engine start information indicate when CONSULT-III screen is touched
• LK WN: Engine start information indicate when CONSULT-III screen is touched
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT-III screen is touched
P RANGE
This test is able to check AT shift selector power supply
• On: Operate
• Off: Non-operation
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is
touched
TRUNK/BACK DOOR
NOTE:
This item is indicated, but not tested
RETRACTABLE MIRROR
This test is able to check auto retractable door mirror operation
• On: Operate
• Off: Non-operation
MIR-14
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
ECU DIAGNOSIS INFORMATION
BCM (BODY CONTROL MODULE)
List of ECU Reference
INFOID:0000000006023378
ECU
Reference
BCM
DOOR MIRROR SYSTEM
MIR-15
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
WIRING DIAGRAM
DOOR MIRROR SYSTEM
Wiring Diagram
INFOID:0000000006007915
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information"
JCLWM4019GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст