Nissan March K13. Instruction — part 460
MIR-16
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000006046392
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much malfunction information (conditions and environment when the mal-
function occurred) as possible when the customer brings the vehicle in.
>> GO TO 2.
2.
REPRODUCE THE MALFUNCTION INFORMATION
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 3.
3.
IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
Use “Symptom diagnosis” from the symptom inspection result in step 2. Then identify where to start the diag-
nosis based on possible causes and symptoms.
>> GO TO 4.
4.
IDENTIFY MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”
Perform the diagnosis with “Component diagnosis” of the applicable system.
>> GO TO 5.
5.
REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 6.
6.
FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Is the malfunctioning part repaired or replaced?
YES
>> Trouble diagnosis is completed.
NO
>> GO TO 3.
DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/
CHANGEOVER SWITCH)
MIR-17
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
DTC/CIRCUIT DIAGNOSIS
DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH/
CHANGEOVER SWITCH)
Component Inspection
INFOID:0000000006007917
1.
CHECK MIRROR SWITCH & CHANGEOVER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check door mirror remote control switch.
[Door mirror (driver side)]
[Door mirror (passenger side)]
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror remote control switch.Refer to
MIR-38, "Removal and Installation"
.
Door mirror remote control switch
Mirror switch condition
Continuity
Connector
Terminal
M7
13
7
RIGHT
Existed
12
4
13
4
LEFT
12
7
13
3
UP
12
7
13
7
DOWN
12
3
Door mirror remote control switch
Mirror switch condition
Continuity
Connector
Terminal
M7
13
6
RIGHT
Existed
12
5
13
5
LEFT
12
6
13
2
UP
12
6
13
6
DOWN
12
2
MIR-18
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH (OPEN/CLOSE SWITCH)
DOOR MIRROR REMOTE CONTROL SWITCH (OPEN/CLOSE SWITCH)
Component Inspection
INFOID:0000000006021973
1.
CHECK OPEN/CLOSE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check door mirror remote control switch.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror remote control switch.Refer to
MIR-38, "Removal and Installation"
.
Door mirror remote control switch
Mirror switch condition
Continuity
Connector
Terminal
M7
13
9
AUTO/OPEN
Existed
12
11
13
11
CLOSE
12
9
POWER SUPPLY AND GROUND CIRCUIT
MIR-19
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
POWER SUPPLY AND GROUND CIRCUIT
DOOR MIRROR REMOTE CONTROL SWITCH (OPEN/CLOSE SWITCH)
DOOR MIRROR REMOTE CONTROL SWITCH (OPEN/CLOSE SWITCH) : Diagnosis
Procedure
INFOID:0000000006021965
1.
CHECK FUSE
Check that the following fuse are not fusing.
Is the fuse fusing?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse are blown.
NO
>> GO TO 2.
2.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness or connector.
Signal name
Fuse No.
IGN power supply
19 (10A)
(+)
(
−
)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
M7
13
Ground
Battery voltage
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
M7
12
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст