Nissan March K13. Instruction — part 685
REAR WIPER ARM
WW-57
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REAR WIPER ARM
Exploded View
INFOID:0000000006067404
Removal and Installation
INFOID:0000000006067405
REMOVAL
1.
Operate rear wiper to the auto stop position.
2.
Remove rear wiper arm cover.
3.
Remove rear wiper arm mounting nut.
4.
Raise rear wiper arm, and remove wiper arm from the vehicle.
INSTALLATION
1.
Clean wiper arm mount as shown in the figure to prevent nut
from being loosened.
2.
Operate rear wiper motor to the auto stop position.
3.
Adjust rear wiper blade position. Refer to
.
4.
Install rear wiper arm by tightening the mounting nut.
5.
Inject washer fluid.
6.
Operate rear wiper to the auto stop position.
7.
Check that rear wiper blades stop at the specified position.
8.
Install rear wiper arm cover.
Adjustment
INFOID:0000000006067406
REAR WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of back door glass and the top of wiper blade center.
1.
Rear wiper blade
2.
Rear wiper motor
3.
pivot seal
4.
Rear wiper arm cover
5.
Rear wiper arm
Refer to
JMLIA1002GB
SKIA0082J
WW-58
< REMOVAL AND INSTALLATION >
REAR WIPER ARM
Standard clearance
L
: 54.5
±
7.5 mm (2.146
±
0.295 in)
JPLIA1236ZZ
REAR WIPER MOTOR
WW-59
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REAR WIPER MOTOR
Exploded View
INFOID:0000000006067407
Removal and Installation
INFOID:0000000006067408
REMOVAL
1.
Remove rear wiper arm cover and rear wiper arm. Refer to
.
2.
Remove back door finisher lower. Refer to
INT-33, "Removal and Installation"
.
3.
Disconnect rear wiper motor connector.
4.
Remove rear wiper motor mounting bolts.
5.
Remove rear wiper motor from the vehicle.
6.
Remove pivot seal.
INSTALLATION
1.
Install pivot seal.
2.
Install rear wiper motor to the vehicle.
3.
Connect rear wiper motor connector.
4.
Operate rear wiper to the auto stop position.
5.
Install back door finisher lower. Refer to
INT-33, "Removal and Installation"
6.
Install rear wiper arm cover and rear wiper arm. Refer to
1.
Rear wiper blade
2.
Rear wiper motor
3.
Pivot seal
4.
Rear wiper arm cover
5.
Rear wiper arm
Refer to
JMLIA1002GB
WW-60
< REMOVAL AND INSTALLATION >
REAR WASHER NOZZLE AND TUBE
REAR WASHER NOZZLE AND TUBE
Hydraulic Layout
INFOID:0000000006067409
Removal and Installation
INFOID:0000000006067410
REMOVAL
1.
Apply protective tape (B) around rear nozzle to protect the
painted surface from damage.
2.
Push pawls with a flat-bladed screwdriver (A) wrapped into a
protective tape.
3.
Remove rear washer tube from rear washer nozzle (1).
INSTALLATION
Install in the reverse order of removal.
1.
Rear washer nozzle
2.
Grommet
3.
Rear washer tube
4.
Washer tank
: Clip
JMLIA1065ZZ
: Pawl
JMLIA1003ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст