Nissan March K13. Instruction — part 469
MWI-14
< SYSTEM DESCRIPTION >
SYSTEM
MODELS WITH ABS
A/T MODELS WITHOUT ABS
M/T MODELS
NOTE:
• Average fuel consumption on the information display is updated approximately every 30 seconds.
• Soon after a reset or when the ignition switch is turned ON right after battery removal and installation, “
−−−
”
is displayed until after a travel of 30 seconds and approximately 500 m (0.31 mile).
Distance To Empty
The combination meter calculates distance to empty based on the following signals, and the calculated value
is displayed on the information display.
MODELS WITH ABS
A/T MODELS WITHOUT ABS
M/T MODELS
NOTE:
Signal name
Signal path
Fuel consumption monitor signal
ECM
Combination
meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
Signal name
Signal path
Fuel consumption monitor signal
ECM
Combination
meter
Vehicle speed signal
TCM
Combination
meter
Signal name
Signal path
Fuel consumption monitor signal
ECM
Combination
meter
Vehicle speed sensor signal
Vehicle speed sensor
Combination meter
Signal name
Signal path
Fuel level sensor signal
Fuel level sensor unit
Combination meter
Fuel consumption monitor signal
ECM
Combination
meter
Vehicle speed signal
ABS actuator and electric unit (control unit)
Combination meter
Signal name
Signal path
Fuel level sensor signal
Fuel level sensor unit
Combination meter
Fuel consumption monitor signal
ECM
Combination
meter
Vehicle speed signal
TCM
Combination
meter
Signal name
Signal path
Fuel level sensor signal
Fuel level sensor unit
Combination meter
Fuel consumption monitor signal
ECM
Combination
meter
Vehicle speed sensor signal
Vehicle speed sensor
Combination meter
MWI
SYSTEM
MWI-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
• Distance to empty on the information display is updated approximately every 30 seconds.
• When the ignition switch is turned from OFF to ON, “
−−−
” is displayed until after a travel of approximately
500 m (0.31 mile).
• The indicated values may not match each other when refueling with the ignition switch ON. Refer to
"INFORMATION DISPLAY : Description"
INTERRUPT INDICATION
Low Fuel Warning
• The combination meter displays a possible cruising distance by an interrupt and blinks the indications of the
fuel gauge and the possible cruising distance when all the following conditions are satisfied.
• The combination meter judges showing/hiding of “low fuel warning”, according to the signals below:
CLOCK
The combination meter displays time on the vehicle information display.
Operating condition
Ignition switch
ON
Fuel remaining quantity
Approximately 9.5
(2-1/8 lmp gal) or less [1.5
(3/8 Imp gal) fuel residues in-
cluded]
Dummy cross-reference("XX-XX")
Signal name
Signal path
Ignition signal
—
Fuel level sensor signal
Fuel level sensor unit
Combination meter
MWI-16
< SYSTEM DESCRIPTION >
OPERATION
OPERATION
Switch Name and Function
INFOID:0000000005883868
JSNIA2972ZZ
Switch name
Operation
Description
Meter control switch (1)
Press
• Trip meter A or Trip meter B can be reset.
• The information display screen can be switched.
• The value of the average fuel consumption can be reset.
• The combination meter can be switched to Self-diagnosis mode.
Clock switch (2)
Press
Time can be adjusted.
MWI
DIAGNOSIS SYSTEM (COMBINATION METER)
MWI-17
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DIAGNOSIS SYSTEM (COMBINATION METER)
On Board Diagnosis Function
INFOID:0000000005883869
ON BOARD DIAGNOSIS ITEM
• Information display operation can be checked in self-diagnosis mode.
• Speedometer and tachometer (with tachometer models) can be checked in self-diagnosis mode.
METHOD OF STARTING
1.
Turn the ignition switch ON while pressing and holding the meter
control switch (1) for 0.8 seconds or more.
2.
Press the meter control switch at least 3 times. (Within 7 seconds after the ignition switch is turned ON.)
3.
The combination meter is turned to self-diagnosis mode.
• Speedometer and tachometer (with tachometer models) return to zero, simultaneously.
• All segments of the information display are displayed.
NOTE:
• Check combination meter power supply and ground circuit when the self-diagnosis mode of the combi-
nation meter does not start. Replace combination meter if power supply and ground circuit are normal.
• If any of the segments are not displayed, replace combination meter.
4.
Each meter activates by pressing the meter control switch.
JSNIA2970ZZ
JSNIA2938ZZ
JSNIA2971ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст