Nissan Primera P12. Instruction — part 487
FSU-14
THIRD LINK
THIRD LINK
PFP:54592
Removal and Installation
EES00142
REMOVAL
1.
Remove kingpin cap with a flat-bladed screwdriver.
2.
Remove nut and washer securing steering knuckle and third link.
3.
Remove nut and washer securing upper link and third link.
4.
Remove mounting bolts, and remove third link from strut.
CAUTION:
Do not disassemble kingpin part of third link.
INSPECTION AFTER REMOVAL
Visual Inspection
Check third link and bushing for deformation, cracks, and other damage. Replace the entire third link assem-
bly if cracks, deformation or any other damage is found.
INSTALLATION
1.
Set third link to kingpin, install washer and nut. Tighten nut to the specified torque.
CAUTION:
The nut is not reusable. Always use a new one.
2.
Pack kingpin cap with multi-purpose grease. Then install the cap to third link.
CAUTION:
The kingpin cap is not reusable. Always use a new one.
3.
Install third link mounting bolts to strut. Tighten bolts to the specified torque.
4.
Install upper link mounting nut and washer to third link. Tighten nut to the specified torque.
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-15
C
D
F
G
H
I
J
K
L
M
A
B
FSU
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
General Specification
EES00143
Wheel Alignment (Unladen)
EES00144
: Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.
Ball Joint
EES00145
Wheelarch Height (Unladen)
EES00146
Suspension type
Independent multi-link strut with coil spring
Shock absorber type
Double-acting hydraulic
Stabilizer bar
Standard equipment
Drive type
2WD
Camber
Degree minute (Decimal degree)
Minimum
−
0
°
55
′
(
−
0.92
°
)
Nominal
−
0
°
10
′
(
−
0.17
°
)
Maximum
0
°
35
′
(0.58
°
)
Left and right difference
45
′
(0.75
°
)
Caster
Degree minute (Decimal degree)
Minimum
1
°
05
′
(1.08
°
)
Nominal
1
°
50
′
(1.83
°
)
Maximum
2
°
35
′
(2.580
°
)
Left and right difference
45
′
(0.75
°
)
Kingpin offset
Degree minute (Decimal degree)
Minimum
13
°
55
′
(13.92
°
)
Nominal
14
°
40
′
(14.67
°
)
Maximum
15
°
25
′
(15.42
°
)
Total toe-in
Distance (A - B)
Minimum
0 mm (0 in)
Nominal
1 mm (0.04 in)
Maximum
2 mm (0.08 in)
Wheel turning angel
Refer to
.
Oscillating torque
0.5 - 3.4 N ·m (0.05 - 0.35 kg-m, 5 - 30 in-lb)
Measurement on spring balance (cotter pinhole position)
7.94 - 53.97 N (0.81 - 5.50 kg, 1.79 - 12.2 lb)
Sliding torque
0.5 - 3.4 N ·m (0.05 - 0.35 kg-m, 5 - 30 in-lb)
Axial end play
0.1 mm (0.004 in) or less
Applied
model
F9Q engine
YD22DDTi engine
F9Q engine
YD22DDTi engine
Sedan
Wagon
205/60R16
215/50R17
205/60R16
215/50R17
205/60R16
215/50R17
205/60R16
215/50R17
SFA818A
FSU-16
SERVICE DATA AND SPECIFICATIONS (SDS)
: Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.
Front (Hf)
mm (in)
698 (27.48)
697 (27.44)
697 (27.44)
696 (27.40)
699 (27.52)
699 (27.52)
698 (27.48)
698 (27.48)
Rear (Hr)
mm (in)
699 (27.52)
696 (27.40)
699 (27.52)
696 (27.40)
695 (27.36)
692 (27.24)
695 (27.36)
692 (27.24)
MODEL P12 SERIES
F9Q / YD 100 kW
* For information on these sections refer to ‘‘P12’’ data
set.
© 2003 NISSAN EUROPE S.A.S.
All rights reserved. No part of this Electronic Service Instruction may be reproduced or stored in a retrieval system, or transmitted in any
form, or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Nissan
Europe S.A.S., Paris, France.
A GENERAL INFORMATION
B ENGINE
C TRANSMISSION/
TRANSAXLE
D DRIVELINE/AXLE
E SUSPENSION
F
BRAKES
G STEERING
H RESTRAINTS
I
BODY
J
AIR CONDITIONER
K ELECTRICAL
L
MAINTENANCE
M INDEX
Supplemental Restraint System (SRS)
Glasses, Window System & Mirrors
Audio, Visual & Telephone System
Power Supply, Ground & Circuit Elements
QUICK REFERENCE INDEX
A
B
C
D
E
F
G
H
I
J
K
L
M
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст