Nissan Primera P12. Instruction — part 684
RAX-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Caution
EDS0015U
Observe the following precautions when disassembling and servicing drive shaft.
●
Perform work in a location which is as dust-free and dirt-free as possible.
●
Before disassembling and servicing, clean the outside of parts.
●
The disassembly and service location must be clean. Care must be taken to prevent parts from becoming
dirty and to prevent the entry of foreign objects.
●
Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean
cover must be placed over parts.
●
Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adher-
ing to parts.
●
Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by
blowing with air or wiping with paper shop cloths.
Precautions for Brake System
EDS0015V
●
When installing rubber parts, final tightening must be carried out
under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack, hand
tools and mats in designated positions.
●
Use flare nut wrench when removing or installing brake tubes.
●
After installing removed suspension parts, check wheel align-
ment and adjust if necessary.
●
Always torque brake lines when installing.
SBR686C
PREPARATION
RAX-3
C
E
F
G
H
I
J
K
L
M
A
B
RAX
PREPARATION
PFP:00002
Special Service Tools
EDS0015W
Commercial Service Tools
EDS0015X
Tool name
Tool number
Description
Drift
KV40100610
a: 54.3 mm (2.138 in) dia.
b: 63 mm (2.48 in) dia.
Removing ABS sensor rotor
Drift
ST15310000
a: 96 mm (3.78 in) dia.
b: 84 mm (3.31 in) dia.
Installing ABS sensor rotor
Drift
KV40105310
a: 89.1 mm (3.508 in) dia.
b: 80.7 mm (3.177 in) dia.
Installing ABS sensor rotor
Drift
KV38100500
a: 80 mm (3.15 in) dia.
b: 60 mm (2.36 in) dia.
Installing hub cap
ZZA0881D
ZZA0908D
ZZA1003D
ZZA0701D
Tool name
Description
1. Flare nut crowfoot
2. Torque wrench
a: 10 mm (0.39 in)
Removing and installing brake piping
S-NT360
RAX-4
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
PFP:00003
NVH Troubleshooting Chart
EDS0015Y
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
Re
fe
r
to
—
Re
fe
r
to
N
V
Hi
nF
A
X
a
n
dF
S
U
s
e
c
ti
o
n
s
.
N
V
H
in
W
T
s
ec
ti
on.
N
V
H
in
W
T
s
ec
ti
on.
NVH
in
F
AX
s
e
c
ti
o
n
.
N
V
Hi
nB
Rs
e
c
ti
o
n
.
NVH
in
P
S
s
e
c
ti
o
n
.
Possible cause and SUSPECTED PARTS
Im
pr
ope
r
in
s
ta
llat
ion,
lo
o
s
ene
ss
Par
ts
int
erf
e
renc
e
Wh
eel
b
ear
in
g
d
am
age
FRONT
A
XLE
A
ND
FRONT
S
USPENSION
TIRES
ROAD
W
EEL
DRI
VE
SHAFT
BRAKES
STEERING
Symptom
REAR AXLE
Noise
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
×
WHEEL HUB
RAX-5
C
E
F
G
H
I
J
K
L
M
A
B
RAX
WHEEL HUB
PFP:43202
On-Vehicle Inspection
EDS0015Z
Inspect to check that there is no excessive play, cracking, wear, or other damage to rear axle.
●
Turn rear wheels (left/right) and check the play.
REAR WHEEL BEARING
With vehicle raised, inspect the following.
●
Move wheel hub in the axial direction by hand. Check that there is no looseness of rear wheel bearings.
●
Rotate wheel hub and check that there is no unusual noise or
other irregular conditions. If there are any irregular conditions,
replace wheel bearing.
●
If any irregular conditions are found, replace ball bearings.
Removal and Installation
EDS00160
REMOVAL
1.
Remove tire.
SMA525A
Axial end play
: 0.05 mm (0.0020 in) or less
SRA690A
MDIA0004E
1
Hub cap
2
Lock nut
3
Wheel hub
4
Hub bolt
5
ABS sensor rotor
6
Back plate
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст