Nissan Primera P12. Instruction — part 685
RAX-6
WHEEL HUB
2.
Remove brake caliper and brake rotor. Refer to
.
CAUTION:
Suspend caliper assembly with wire so as not to stretch
brake hose.
Be careful not to depress brake pedal, or piston will pop
out.
3.
Remove wheel lock nuts.
4.
Remove wheel hub from spindle.
5.
Remove ABS wheel speed sensor.
6.
Remove back plate.
7.
Remove the sensor rotor using suitable puller, drift and bearing
replacer.
INSPECTION AFTER REMOVAL
Inspect wheel hub for deformation, cracks, and other damage. If any irregular conditions are found, replace
wheel hub.
INSTALLATION
1.
With vehicles equipped with ABS, press-fit ABS sensor rotor into
wheel hub bearing using a drift.
CAUTION:
Do not reuse ABS sensor rotor.
When installing, replace it with a new one.
Press-fit ABS sensor rotor as far as location shown in figure at right.
2.
Install wheel hub.
3.
Tighten wheel bearing lock nut.
Before tightening, apply oil to threaded portion of rear spindle.
SRA692A
MDIA0005E
MDIA0006E
SDIA0223J
WHEEL HUB
RAX-7
C
E
F
G
H
I
J
K
L
M
A
B
RAX
CAUTION:
Do not reuse wheel bearing lock nut.
4.
Tighten wheel hub lock nuts to specified torque. Rotate in for-
ward and reverse direction 10 times each to ensure a good fit.
5.
Place a spring balance at the point where the hub bolt and mea-
sure rotation torque when spring is pulled at a speed of 8 to 12
rpm.
6.
Check wheel hub bearing axial end play.
7.
Clinch two places of lock nut.
8.
Install hub cap.
CAUTION:
Do not reuse hub cap. When installing, replace it with a new
one.
: 187.0 - 254.8 N·m (19 - 25 kg-m, 138 - 187 ft-lb)
Rotation torque
: 0.191 - 1.280 N·m (0.02 - 0.13
kg-m, 2 - 11 in-lb)
Spring balance
reading
: 3.3 - 22.4 N (0.34 - 2.28 kg,
0.74 - 5.04 lb)
Axial end play:
Less than 0.05 mm (0.0020 in)
SRA693A
SRA737A
SFA599B
RAB0349D
RAX-8
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Wheel Bearing
EDS00161
Drive type
2WD
Rotation torque
0.191 - 1.280 N·m (0.02 - 0.13 kg-m, 2 - 11 in-lb)
Spring balance reading
3.3 - 22.4 N (0.34 - 2.28 kg, 0.74 - 5.04 lb)
Installation location of spring balance
Hub bolt
Wheel hub lock nut tightening torque
187.0 - 254.8 N·m (19 - 25 kg-m, 138 - 187 ft-lb)
Axial end play
0.05 mm (0.0020 in) or less
RSU-1
REAR SUSPENSION
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION
A
B
RSU
REAR SUSPENSION
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Caution . . . . . . . . . . . . . . . . . . 2
Precautions for Brake System . . . . . . . . .. 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tool . . . . . . . . . . . . . 3
Commercial Service Tools . . . . . . . . . . 3
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 4
NVH Troubleshooting Chart . . . . . . . . . . 4
REAR SUSPENSION ASSEMBLY . . . . . . . . 5
DESCRIPTION . . . . . . . . . . . . . .. 5
PRELIMINARY INSPECTION . . . . . . . ... 5
CAMBER . . . . . . . . . . . . . . . ... 6
TOE-IN . . . . . . . . . . . . . . . . .. 6
Removal and Installation . . . . . . . . . . .. 6
REMOVAL . . . . . . . . . . . . . . . . 6
INSTALLATION . . . . . . . . . . . . . . 7
COIL SPRING AND SHOCK ABSORBER . . . . . 8
Removal and Installation . . . . . . . . . . .. 8
REMOVAL . . . . . . . . . . . . . . . . 8
INSTALLATION . . . . . . . . . . . . . . 8
Disassembly and Assembly . . . . . . . . . .. 8
DISASSEMBLY . . . . . . . . . . . . . . 8
INSPECTION AFTER DISASSEMBLY . . . . .. 8
ASSEMBLY . . . . . . . . . . . . . . ... 9
LATERAL LINK AND CONTROL ROD . . . . . 10
Removal and Installation . . . . . . . . . . 10
STABILIZER BAR . . . . . . . . . . . . . . 11
Removal and Installation . . . . . . . . . . 11
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст