Nissan Primera P12. Instruction — part 630
MT-26
[RS6F51R]
TRANSAXLE ASSEMBLY
2.
Using a drift, install differential oil seal until the face is flush with
clutch housing.
CAUTION:
Do not reuse oil seal.
3.
Install oil channel on mainshaft side.
CAUTION:
Be careful with orientation of installation.
4.
Using a drift, install mainshaft front bearing.
CAUTION:
Be careful with orientation of installation.
5.
Install bearing retainer.
CAUTION:
Install with punched surface facing up.
MCIA0032E
SCIA0986E
SCIA0401E
SCIA0400E
TRANSAXLE ASSEMBLY
MT-27
[RS6F51R]
D
E
F
G
H
I
J
K
L
M
A
B
MT
6.
Install differential side bearing outer race.
7.
Install final drive assembly into clutch housing.
8.
Install input shaft assembly, mainshaft assembly, and reverse
idler gear assembly into clutch housing.
CAUTION:
Be sure not to damage input shaft oil seal.
9.
Install 1st-2nd fork rod bracket onto 1st-2nd fork rod, and then
install retaining pin.
CAUTION:
Do not reuse retaining pin.
MCIA0016E
SCIA0888E
SCIA0964E
SCIA0889E
MT-28
[RS6F51R]
TRANSAXLE ASSEMBLY
10. Install 1st-2nd fork rod and 1st-2nd shift fork, and then install
retaining pin.
CAUTION:
Do not reuse retaining pin.
11. Install shift check sleeve.
12. Install 3rd-4th bracket, 3rd-4th shift fork, and 3rd-4th fork rod
with inter lock pin.
13. Install stopper ring onto 3rd-4th shift fork.
CAUTION:
Do not reuse stopper ring.
14. Install retaining pin onto 3rd-4th bracket.
CAUTION:
Do not reuse retaining pin.
15. Install 2 check balls.
16. Install 5th-6th bracket, 5th-6th shift fork, and 5th-6th fork rod
with interlock pin.
17. Install stopper ring onto 5th-6th bracket.
CAUTION:
Do not reuse stopper ring.
18. Install retaining pin onto 5th-6th shift fork.
CAUTION:
Do not reuse retaining pin.
19. Install 2 check balls.
20. Install reverse bracket fork rod and reverse lever bracket.
SCIA0394E
SCIA0393E
SCIA0963E
SCIA0962E
TRANSAXLE ASSEMBLY
MT-29
[RS6F51R]
D
E
F
G
H
I
J
K
L
M
A
B
MT
21. Install retaining pin onto reverse bracket.
CAUTION:
Do not reuse retaining pin.
22. Install reverse shift fork and reverse fork rod.
23. Install reverse lever assembly following procedures below.
a.
Install shifter cap onto reverse lever assembly cam, and then
install them onto reverse shift fork.
CAUTION:
Do not drop shifter cap.
b.
While lifting reverse shift fork, align cam with reverse bracket.
c.
Tighten mounting bolts to specified torque, and then install
reverse lever assembly.
24. Install the magnet onto clutch housing.
25. Using a drift, install differential oil seal until it is flush with end
face of transaxle case.
CAUTION:
Do not reuse oil seal.
26. Install selected input shaft adjusting shim onto input shaft.
●
For selection of adjusting shims: Refer to
.
27. Install baffle plate and oil gutter.
28. Install transaxle case following procedures below.
a.
Install selected mainshaft rear bearing adjusting shim into transaxle case.
●
For selection of adjusting shims: Refer to
.
b.
Temporarily install snap ring of mainshaft rear bearing into transaxle case.
CAUTION:
Do not reuse the snap ring.
SCIA0961E
SCIA0965E
SCIA0960E
SCIA0887E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст