Nissan Primera P12. Instruction — part 629
MT-22
[RS6F51R]
TRANSAXLE ASSEMBLY
4.
Remove check plugs (4 pieces), check springs (4 pieces), check
balls (4 pieces) and shift check sleeve (2 pieces).
5.
Remove transaxle case fixing bolts.
6.
Remove bore plug.
CAUTION:
Be careful not to damage transaxle case.
7.
While spreading the snap ring of mainshaft rear bearing located
at bore plug hole, remove transaxle case.
8.
Remove oil gutter, baffle plate.
9.
Remove snap ring, mainshaft rear bearing adjusting shim and
input shaft rear bearing adjusting shim from transaxle case.
10. Remove differential side bearing outer race (transaxle case
side) and then adjusting shim.
11. Remove welch plug.
SCIA0959E
SCIA0983E
SCIA0897E
SCIA0402E
TRANSAXLE ASSEMBLY
MT-23
[RS6F51R]
D
E
F
G
H
I
J
K
L
M
A
B
MT
12. Remove differential oil seal (transaxle case side).
13. Remove magnet from clutch housing.
14. With shift lever in 5th position, remove bracket bolts from
reverse lever assembly. Lift reverse lever assembly to remove.
CAUTION:
Be careful not to lose shifter cap.
15. Pull out reverse fork rod then remove reverse shift fork.
16. Remove retaining pin of reverse bracket using pin punch.
17. Pull out reverse bracket and reverse bracket fork rod.
18. Remove check ball (2 pieces) and inter lock pin.
19. Shift 3rd & 4th fork rod to 3rd position. Remove retaining pin of
5th & 6th shift fork using pin punch.
SCIA0397E
SCIA0960E
SCIA0961E
SCIA0962E
MT-24
[RS6F51R]
TRANSAXLE ASSEMBLY
20. Remove stopper rings for 5th & 6th bracket.
21. Pull out 5th & 6th fork rod and remove 5th & 6th shift fork and
5th & 6th bracket.
22. Remove check balls (2 pieces) and inter lock pin.
23. Remove retaining pin of 3rd & 4th bracket using pin punch.
24. Remove stopper rings for 3rd & 4th shift fork.
25. Pull out 3rd & 4th fork rod and remove 3rd & 4th shift fork and
bracket.
26. Remove shift check sleeve from clutch housing.
27. Remove retaining pin of 1st & 2nd shift fork using pin punch.
28. Pull out 1st & 2nd fork rod with bracket.
29. Remove 1st & 2nd shift fork.
30. Remove retaining pin of 1st & 2nd bracket using pin punch and
separate fork rod and bracket.
31. Remove gear components from clutch housing in the following
procedure.
a.
While tapping input shaft with plastic hammer, remove input
shaft assembly, mainshaft assembly and reverse idler gear
assembly as a set.
CAUTION:
Always withdraw mainshaft straight out. Failure to do so
can damage resin oil channel on clutch housing side.
b.
Remove final drive assembly.
SCIA0963E
SCIA0393E
SCIA0394E
SCIA0964E
TRANSAXLE ASSEMBLY
MT-25
[RS6F51R]
D
E
F
G
H
I
J
K
L
M
A
B
MT
32. Remove mainshaft bearing retainer and then mainshaft front
bearing.
33. Remove oil channel on mainshaft side.
34. Remove differential oil seal (clutch housing side).
35. Remove differential side bearing outer race (clutch housing
side).
36. Remove input shaft oil seal.
CAUTION:
Be careful not to damage clutch housing.
ASSEMBLY
1.
Using a drift, install input shaft oil seal from clutch housing end
of side to the depth of 1.8 to 2.8 mm (0.071 to 0.110 in).
CAUTION:
Do not reuse oil seal.
MCIA0030E
MCIA0031E
SCIA0398E
SCIA0399E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст